Water at 25°C is flowing through a 1.0 km long Gl pipe of 200 mm diameter at the rate of 0.07 m3/s. If value of Darcy friction factor for this pipe is 0.02 and density of water is 1000 kg/ m', the pumping power (in kW) required to maintain the flow is (а) 1.8 (c) 20.5 (b) 17.4 (d) 41.0

Water at 25°C is flowing through a 1.0 km long Gl pipe of 200 mm diameter at the rate of 0.07 m3/s. If value of Darcy friction factor for this pipe is 0.02 and density of water is 1000 kg/ m', the pumping power (in kW) required to maintain the flow is (а) 1.8 (c) 20.5 (b) 17.4 (d) 41.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I1
A pump with a suction and discharge pressure of 125kPa and 409 kPa respectively, discharges water at 30L/s to a 4 cm diameter pipe. The suction diameter is 10 cm. Determine the energy added to the water by the pump. Select the correct response: 57.25 m 48.22 m 88.12 m 64.25 m
Three pipes are connected in series with properties given as: for pipe A, L= 300 m, diameter = 15 cm, for pipe B, L= 400 m, diameter= 20 cm and for pipe C, L= 600 m, diameter= 25 cm. The Manninbg's coefficient of the three pipes n= 0.011. If the total frictional losses is 5 m, excluding minor losses, determine the amount of water flowing through the pipe system. a.35 L/s b.20 L/s c.25 L/s d.30 L/s
The discharge in a pipeline delivering water under gravity between reservoirs with water surface elevations of 150m and 60m is to be boosted by the installation of a centrifugal pump with the tabulated characteristics. Pump Characteriticis Q (L/s) Hp (m) 50 100 150 200 250 50.0 49.0 46.5 42.0 36.0 28.2 The pipeline is 15km long, 350mm in diameter, and has a friction factor of A=0.02. Assume minor losses v2 Determine the discharge in the system: 2g amount to 20- a) under gravity flow conditions b) with the booster pump installed. *Hint: Plot the system curve vs the pump curve using the graph space in Figure 2 and determine the duty point. Note that affect of the booster pump is to increase the system head.
1 and 2 water (r = 1005 kg / m3, m = 1.807´10-3 kg / m × s) are connected by 40 m long 2 cm long plastic pipes. Losses next to losses in the piping system may be the cause of their losses. The water level in both chambers is the same, but 1 chamber is pressurized with compressed air and 2 chambers are open to the atmosphere at 88 kPa. Calculate the absolute air lemon in 1 chamber according to the initial flow rate in the pipe 1.2 L / s.
Water is being pumped from a reservoir with water surface elevation of 12 m to another reservoir at elev. 69 m at the rate of 25 L/s. The pump is located at elevation 2 m. The pipe leading from the lower reservoir to the suction side of the pump has Manning’s n=0.011 and is 15 m long and 250 mm in diameter. The pipe from the discharge side of the pump to the upper reservoir is 600 m long and 200 mm in diameter with a friction factor f=0.02. Determine the horsepower required by the pump if its efficiency is 70%.
Determine the pumping power (in kW) required, if water at 30°C is flowing through a pipe length of 1km with 250 mm diameter at the rate of 0.05 m³/s. Take value of Darcy friction factor as 0.04
Water at 20 °C is being stored in a large, insu lated tank shown below. It is being recycled to the same tank by apump at an in itial ve locity of 3 m/s through apipe with a diameter of 5.25 cm. The pump supplies 98 j/kg of fluid. The exit pipe from the pump is 3.5 cm diameter and the exit pressure is 80 kN/m? abs. If the frictional loss in the pipe system is 31.5 jkg, calcu late entrance pressure of the fluid (P1) 6.0 m 3.5 cm P2 U2 VI Pi5.25 cm Ws
Water with a temperature of 20 oC is pumped from a tank open to the atmosphere (zA = 2.90 m), through two cast iron (roughness value ε=0.005mm) pipes of 29 m length, connected in parallel with the higher one (zB = 9.9 m). Pipe diameters are D1 = 3.9 cm and D2 = 5.9 cm, respectively. The water is pumped with a motor-pump group, whose efficiency is 69% and consumes 7090 W of electrical power during operation. miner losses in pipes connecting parallel pipes to tanks are neglected. Find the total volume flow rate between the tanks and the volume flow rate in each of the parallel pipes. Solve the problem by making at least three iterations.
Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss due to friction is O 1. 1m O 2. 10 m 0 3.0.1 m 0 4.9.81 m
For a fully developed flow of water in a pipe having diameter 10 cm, velocity 0.1 m/s and kinematic viscosity 10-5 m²/s, the value of Darcy friction factor is
Engine oil at 20 C flows in a 14-cm-diameter pipe at a rate of 900 L/min. The friction factor for this flow is