Water at 20°C is siphoned from a reservoir as shown in following figure. For d = 8 cm and D = 16 cm, determine (a) the minimum flow rate that can be achieved without cavitation occurring in the piping system at points 2 and 3 and (b) the maximum elevation of the highest point of the piping system to avoid cavitation. (c) Draw the HGL and the EGL for this system? H (m) 4.0 HT= 20°C ա լ | 2 m 7m

Q: Water Resource Engineering: Open Channel Flow For a triangular channel, the top width, T is given…

A: Given data: Calculating critical depth using the given relation: Given relation:

Q: What is the critical depth in a rectangular channel with 2.3 m width and 0.91 m2/s discharge per…

A: What is the critical depth in a rectangular channel and calculate minimum specific energy?

Q: Two pipes are connected in parallel between two reservoirs: L1= 2000 m, D1= 160 cm, C1=120; L2= 1400…

A: Given: Two pipes connected in parallel,L1 = 2000 m     L2 = 1400 mD1 = 160 cm    D2 = 800 mmC1 = 120…

Q: Three Reservoirs A B and C are connected by pipes 1, 2 and 3 respectively which meets at the…

A: Given: Pipe 1 (D=300 mm; L = 450 m; f=0.0198) Pipe 2 (D=150 mm; L = 240 m; f=0.0175) Pipe 3 (D=200…

Q: Two rectangular clarifiers which are connected in series, each 50 m long and 15 m wide with water…

A: For Two rectangular clarifiers which are connected in series,Length,L  50 mWidth,B= 15 m wide Depth…

Q: The water is passed through a steel pipe with a diameter of 23 cm (rough height 0.046 mm) out of the…

A: Given, D = 23 cm or 0.23 m  L = 200 m

Q: (viscosity: v = 1 × 10-6 m² /s, SG = 0.9) flows from the upper voir at a rate of 0.028 m³/s in the…

A:

Q: Q10. The three water filled tanks shown in the figure are connected by pipes as indicated. If minor…

A: To determine:the flow rate in each pipe.

Q: 2. It is known that an irrigation channel has a rectangle with width (b) = 4.5 m, height (h) = 5 m,…

A:

Q: Nozzle

A: To calculate pressure head at point 2. Applying Bernoullis equation at point 2 and exit. Note that…

Q: A pump is installed in the pipeline between reservoirs A and E as shown in the figure below. Water…

A: Given, Hazan Williams  coefficient =120 discharge Q=10 ft3/s Elevation A and B is 25ft and 40 ft

Q: 1 Μ Figure 2 2 ↓ Δε

A:

Q: Water flows from a tank through a 23 cm diameter steel pipe. Determine (a) the discharge of water,…

A:

Q: Water is being discharged from an upper reservoir to a lower reservoir through a turbine (assume 80%…

A: Given  Discharge = 0.15 cumec Efficiency = 80%  Height difference = 197.3- 50 = 147.3 m To calculate…

Q: Three new cast-iron pipes connected in series have diameters of 30 cm, 25 cm, and 20 cm, each being…

A: DIA  D1 = 30CM D2 = 25CM D3= 20 CM LENGTH = 200M discharge is 100 liters per second N= .011

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.