Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge is 5 m above the floor, and friction losses in the 50-mm pipe from the reservoir to the tower amount to 2.5 J/kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 kW?The Reynolds number of this flow is what? Take the viscosity of the water to be 0.001 Pa*s

Q: Water at 20 degree C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the…

A: Introduction In this issue, we apply the Bernoulli equation between the discharge level and the top…

Q: Lane has two pipes connected to each other that transport water because he is very thirsty. The…

A:

Q: rough a pip ean veloci ICI

A:

Q: a cylindrical tank 90 cm high and 60 cm in diameter, open to the atmosphere, initially completely…

A:

Q: air flows in a duct at the rate of 0.056 m3/s. Determine the pressure drop (kPa) between the 6 and 3…

A:

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: 480 kPa 15 cm Water 445 kPa Reducer 8 cm

A: Flow through pipe given- d1=15cmd2=8cmQ=0.035 m3/sec

Q: A reducing elbow is used to deflect and accelerate the flow of water from a horizontal pipe to 30 °…

A: Given: The pipe angle, θ = 30° The mass flow rate, m = 14 kg/s The cross-section area at inlet, A1 =…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A:

Q: In a water hammer experiment, water flows from a tank through a pipe of diameter 0.05 m and length 5…

A: Solution: Given Data: d=0.05 ml=5 mPt=2.9 kPaPL=100 Paf=0.004K=2 GPaρ=1000 kg/m3   To Find:

Q: the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily…

A:

Q: In a hydroelectric power plant as shown in the figure, 100 m3/s of water flows froman elevation of…

A: Given Volumetric flow = 100 m3/s Elevation = 130 m Overall efficiency = 0.8 % To find Electric power…

Q: Question 3 Water enters a U-shape pipe at 50 kg/s mass flow rate at inlet 1 and leaves the U-shape…

A: Given:P1 = 300 kPaP2 = 200 kPaP3 = 100 kPad1 = 5 cmd2 = 10 cmd3 = 3 cmDensity of water = 1000…

Q: the minimum power required

A: Given; Determine the minimum power required to pump the water across the pipe ?Where,  Pressure drop…

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

A:

Q: Water is flowing through a horizontal pipe of diameter 250 mm. If the pressure drop between two…

A: Givend=250mm∆P=825Pa

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: A liquid is pumped at 6,251 N / s between two tanks. Tank A is pressurized to 0.259 MPa and the…

A:

Q: Two long pipes in parallel are used to carry water between two reservoirs. The diameter of one pipe…

A:

Q: In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.55 m³/s…

A: Let us assume that flow is incompressible with steady flowrate. Disregarding the minor losses…

Q: A liquid of specific gravity 1.75 flows in a 6cm pipe. The total energy at a point in the flowing…

A: SG=1.75 d=6cm=0.06mE=80 J/N=80mz=2.60mP=75 kPaV=?

Q: low rate of 0.37 m/min from a lower reservoir as shown in the figure below. The twe eservoirs are…

A: Given:η=0.60Q=0.37 m3/mind=2.54 cm =0.0254 mK=2.9

Q: Water at 90°C is to be pumped from a low-elevation reservoir to a high-elevation reservoir at a flow…

A: The length of the suction pipe→L=7.2 m Flow rate of the water→Q=0.0046 m3/s Friction factor of the…

Q: Underground water is being pumped into a pool section 10 ft x 14 ft while water is discharged…

A: V2=Mean velocity =16.5 ft/secD2=diameter of orifice= 2 in=16 ftproperties of  pool section=10 ft× 14…

Q: Water is flowing through a circular pipe made of cast iron with a diameter of 26 cm. If Reynolds…

A: Given,  Flow of water through pipe Reynolds number (Re) = 105 Concept: Since Reynolds number (Re)…

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: A 2-kW pump is used to pump kerosene (p = 0.820 kg/L) from a tank on the ground to a tank at a…

A: Given,Power P = 2 KW = 2000 WDensity of kerosene = (rho = 0.820 kg / L)Elevation differences between…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A:

Q: Water at 5°C is drained from a large reservoir using 2 horizontal copper pipes connected in series…

A:

Q: Water is flowing through a horizontal pipe. Water enters the left side of the pipe at a pressure P =…

A:

Q: In a pumping system handling water, the surface level of water in the open suction tank is 3m below…

A: The suction level below the pump center is hs=3 m. The delivery level above the pump center is hd=21…

Q: A pump has a required NPSH of 3.0 m. Assuming that the pump is elevated at 3.5 m above sea level,…

A:

Q: Water is sent to a cylindrical tank with a height of 3 m and a diameter of 1 m through a pipe with a…

A:

Q: Consider water flowing through the pipe and reservoir system shown below. The pipe has a diameter of…

A:

Q: A fan is used to extract 140m3 air per minute from a large room. A circular duct of diameter 0.53 m…

A: Given Q=140 m3/min; D1=D2=0.53; D3=0.8m h=6mm To Find: static and stagnation pressure upstream and…

Q: Water, an incompressible fluid, is flowing in a horizontal pipe at a velocity of varg = 1.15 m/s.…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.