Water at 15°C (p = 999.1 kg/m³) from a garden hose fills a 1.5-L container in 2.7 s. Assume that the volume flow rate, temperature, and density of water are constant over the measured time. Calculate the volume flow rate in liters per minute (Lpm). (You must provide an answer before moving on to the next part.) The volume flow rate is 33.33 Lpm.

Water at 15°C (p = 999.1 kg/m³) from a garden hose fills a 1.5-L container in 2.7 s. Assume that the volume flow rate, temperature, and density of water are constant over the measured time. Calculate the volume flow rate in liters per minute (Lpm). (You must provide an answer before moving on to the next part.) The volume flow rate is 33.33 Lpm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pressurized tank contains water with some air above it. As shown on figure below. Multi-fluid manometer is used to determine the pressure at the air-water interface ( If hi= 0.7 m, hz=0.4 m, h3=D0.55 m and ha = 0.85 m. Also, specific gravity of water = 1 and specific gravity of crude oil = 1.8 and specific gravity of mercury 12.5 and specific gravity of shale oil = 2.5 Determine the absolute pressure at point 5 in Pascal unit. [Given: g =9.81 m/s2 and atmospheric pressure 101300 Pa] Mercury S.G. 125 Water S.G. -1 he Crude oil S.G. 18 Shale oil S.G. 25
The table below contains the conditions of a fluid (SG = 0.50) flowing in a pipe having constant diameter: PA 32.4 psi ZA 29.7 psi 56.8 ft Ze 68.2 ft (a) What is the head loss (ft)? (b) Is the flow from A to B or from B to A?
The venturi meter shown below carries water at 60°C. The inside dimensions are machined to the sizes shown in the figure. The specific gravity of the gage fluid in the manometer is 1.25. Calculate the velocity of flow at section A and the volume flow rate of water. 200-mm inside diameter Flow 0.46 m y is an unknown distance y 300- mm inside diameter 1.18 m
A cylindrical tank 400 mm in diameter, discharges water through a 30 mm orifice under a constant head of 5 meters (with reference to the orifice centerline). If it takes about 10 seconds to fill 42 liters of a volumetric measuring tank. Use g =9.8m/s² What is the theoretical flowrate (m³/s)?
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
8. Compute the probable density of a fluid inside a floating spherical balloon having a 2m diameterif the tension in the balloon’s tie rope is observed to be 2kgf. Assume that the density of air is1.18kg/m3. a. 0.7225kg/m3 b. 0.6225kg/m3 c. 0.7025kg/m3 d. 0.5848kg/m3
12 litre/s 4.5 litre/s 5. Water is flowing in a pipe system shown below. The diameters of all pipes are 150mm. Calculate the flow rate and the flow velocity in all pipes. 3.8 litre/s 4.3 litre/s 4.4 litre/s 2.3 1litre/s 3.3 litre/s M 4.2 litre/s 2.6 litre/s
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
2- The density of a liquid is to be determined by an old 1-cm-diameter cylindrical hydrometer whose division marks are completely wiped out. The hydrometer is first dropped in water, and the water level is marked. The hydrometer is then dropped into the other liquid, and it is observed that the mark for water has risen S cm above the liquid-air interface. If the height of the original water mark is 12.7 cm, determine the density of the liquid S (cm) Last names starting 0.95 with A to L Unknown liquid Mark for water S cm
1. Water at 10°C is flowing at 0.075 m3/s. Calculate the weight flow rate and the mass flow rate.
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes