Water at 158°C (r = 999.1 kg/m3 and μ = 1.138 x 10-3 kg/ms) is flowing steadily in a 30-m-long and 5-cm-diameter horizontal pipe made of stainless steel at a rate of 9 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.

Water at 158°C (r = 999.1 kg/m3 and μ = 1.138 x 10-3 kg/ms) is flowing steadily in a 30-m-long and 5-cm-diameter horizontal pipe made of stainless steel at a rate of 9 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of 0.35 m3/s . If the head loss in the pipe is not to exceed 20 m, determine the minimum diameter of the duct (a) Now the duct length is doubled while its diameter is maintained constant. If the total head loss is to remain constant, determine the drop in the flow rate through the duct.
A vented tanker is to be filled with fuel oil with p = 920 kg/m³ and μ = 0.045 kg/m-s from an underground reservoir using a L=25-m-long, 4-cm-diameter plastic hose with a slightly rounded entrance and two 90° smooth bends. The elevation difference between the oil level in the reservoir and the top of the tanker where the hose is discharged is 5 m. The capacity of the tanker is 18 m³ and the filling time is 30 min. Taking the kinetic energy correction factor at the hose discharge to be 1.05 and assuming an overall pump efficiency of 82 percent, determine the required power input to the pump. Tanker 18 m³ 4 cm- ✓ Lm Pump The required power input to the pump = KW
A water tank is attached to a piping system with a sharp edge inlet (KL=0.5). Determine the velocity of the outlet water if the system has two elbow pipes (KL=1.5), the length of the entire system is 10m, the diameter is 1.5cm, the friction factor is 0.002 and the height between the water and the outlet are 5m.
The drinking water to a village is supplied from a reservoir which is 475 m above and 25 km away from the village. The water is transported from the reservoir to an open-top storage tank in the village via a circular pipe with a diameter of 18 cm and a roughness of 0.15 mm. The population of the village is 1500 people. There are two valves (K=2) and five 90° elbows (K=1.5) along the pipe. Assuming that an average person in the village consumes 225 L/day, determine the power (kW) of the pump needed to transter the water from the reservoir to the storage tank. You can take the density and viscosity of water as 1000 kg/m and 0.001 kg/m s, respectively, and you can neglect the inlet and exit losses and the kinetic energy correction factor effects.
Water drains from a pressurized tank (50 kPa gage) through a 0.1m-diameter pipe system at a rate of 0.0371 m³/s. If the density of water is 1000 kg/m³ and the dynamic viscosity is 1.12 x 10 - 3 Ns/m², the Reynolds number would be equal to O 3312 O 25893 O 422321 O 475892
As shown, water at 15°C is flowing in a 19 cm-diameter by 60 m-long run of pipe that is situated horizontally. The mean velocity is 2 m/s, and the head loss is 7 m. Determine the required pumping power in Watts to overcome head loss in the pipe. -Component Pump Water 60m- 3890.015 38900.015 O 3147.291 O 4209.176
Glycerin (p = 1252 kg/m³ and µ = 0.27 kg/m·s) is flowing steadily in a rectangular shape with dimensions 3 cm×2 çm, 15-m-long pipe at an average velocity of 3.5 m/s. Determine the flow type.
In a laminar flow through a circular tube of radius of R, the velocity and temperature profiles at a cross section are given by u = u0 (1- r2/R2) and T(r) = A 1+Br2 - Cr4 where A, B and C are positive constants. Obtain a relation for the bulk fluid temperature at that cross section.
Glycerin at 10°C is flowing steadily through a 8-cm diameter pipe at 0.1 kg/s. What is the average velocity of the glycerin flow? What is the Reynolds number?
Water is transported by gravity through a 10-cmdiameter 550-m-long plastic pipe with an elevation gradient of 0.01 (i.e., an elevation drop of 1 m per 100 m of pipe length). Taking ? = 1000 kg/m3 and ? = 1 × 10−6 m2/s for water, determine the flow rate of water through the pipe. If the pipe were horizontal, what would the power requirements be to maintain the same flow rate?
A 2.4-m-diameter tank is initially filled with water 4 m above the center of a sharp-edged 10-cm-diameter orifice. The tank water surface is open to the atmosphere, and the orifice drains to the atmosphere. Neglecting the effect of the kinetic energy correction factor, calculate (a) the initial velocity from the tank and (b) the time required to empty the tank. Does the loss coefficient of the orifice cause a significant increase in the draining time of the tank?