Water (assumed inviscid and incompressible) flows steadily with a speed of 11 ft/s from the large tank shown in the figure below. Determine the depth, H, of the layer of light liquid (specific weight = 51 lb/ft³) that covers the water in the tank. H= i ft Water 2ft 3ft

Q: 1. The appropriate punch size for a blanking operation using to perform a cold-rolled steel (half…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 2. An automatic bending machine requires a very large torque and slow rpm. Suppose you are to design…

A: It is asked to reduce the RPM from 1400 RPM to 18 RPM by using spur gear combinations

Q: Write a detail note on “Tube Drawing with Mandrels”.

A: Tube drawing is metal forming process in which tube is drawn from a metal stock by plastic…

Q: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm…

A: Given, Diameter of hole, d=45mmThickness of plate,t=20mmTorque,T=7Nm of sheared areaCutting…

Q: (b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to…

A:

Q: For symmetric and large circular section which pattern is preferred

A: Given: Symmetrical and large circular section To explain Which pattern required for Symmetrical and…

Q: the blanks: the center distance in (cm) of 4 direct contact rolling.cylinders. Cylinders A-D have a…

A:

Q: omproper heating of the metal at high temperature in Forging or for a long time causing Brunt and…

A: Heating of the metal at high temperature in forging or for a long time causing Brunt and overheated…

Q: 9. A sheared component 60 inches long has a tolerance of +/-2 degrees along the length. What would…

A: Shearing is a metalworking process that cuts or separates a sheet of metal along a straight…

Q: i still dont think i am getting the full working how you get to 0.32, am going to need to see the…

A: Given Data

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: The objective of the question is to calculate the flow rate required to retract the hydraulic press…

Q: What is the force required to punch a 20-mm diameter hole in a plate that is 25 mm thick? Shear…

A:

Q: rance for bl ce of 2% pe се

A:

Q: time

A: 65.5 sec

Q: pieces of sheet metal are to be u-formed using a single-acting cylinder. the start signal is to be…

A: The problem involves a single-acting cylinder that is used to U-form pieces of sheet metal. The…

Q: Calculate the force required to shear a 0.7" dia. hole through a 0.16" thick piece of yellow brass.…

A: Given data: The diameter of the hole is d = 0.7 in. The thickness of the plate is t = 0.16 in. The…

Q: From the data, determine the size of the punch, for a circular blanking operation

A: As per given question  Size of the blank =30mm Thickness of the sheet=3 mm Radial clearance b/w…

Q: Explain the difference between sweep vs segmental pattern.

A:

Q: 5- Which of the following material can be used to produce Tools a. Glasses b. Elastomers c. High…

A:

Q: With the help of a labelled schematic diagram show the path of a warp yarn in a High Speed modern…

A: the diagram shows the path of wrap yarn in high speed modern warping machine

Q: Energy required to cut a hole. Energy required for cutting work per second. Maximum fluctuation of…

A:

Q: What is the cutting speed of a material with a radius of 40 mm and a speed of 1000 rpm?

A:

Q: 11) Define the cornering stiffness.

A: When the vehicle is moving at a high speed the lateral acceleration will develop in the tire due to…

Q: 4. The drilling speed for cast iron is assumed to be 70 ft/min. Find the time required to drill two…

A:

Q: Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking…

A: The shearing force is given by, Fshear=0.7×σu×T×L where, T = sheet thickness = 2.5 mm L = total…

Q: What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length…

A:

Q: For bar drawing, semi-die angle.may vary between a. 0 and 5 degree b. 20 and 25 degree 6 and 20…

A: Bar drawing is the process in which workpiece in the form of cylindrical bar or rod is pulled…

Q: 9) Define the rolling resistance.

A: We are to define rolling resistance.

Q: 6. How large of a square may be milled on the end of a 2 1/2-inch bar of round stock? Page #

A: The largest square that can be milled on the end of a 221​inches bar of round stock would have sides…

Q: 5- Complete the sentence with the correct statement for rolling operation. In the the strip is…

A: To fill :- In the ................. the strip is rolled continuously, through a number of stands.…