Wastewater containing lead is being released from a certain industrial plant. The stream contains 7.74 % Pb and is treated in a unit (maximum capacity = 5000 kg wastewater/hr) that removes 90% of lead in the feed, which is then recycled back into the plant. Another stream from the unit is being released to a lagoon. If the stream leaving the plant has a rate greater than that of the treatment unit. the excess of the capacity of the unit (say. the excess above 5000 kg/hr) bypasses the unit. This excess is combined with the liquid leaving the treatment unit, which is released into the lagoon. The treatment plant releases 7500 kg/hr of wastewater. Determine the flow rate of the liquid to the waste lagoon. Include units. Express your answer in 1 decimal place only.

Wastewater containing lead is being released from a certain industrial plant. The stream contains 7.74 % Pb and is treated in a unit (maximum capacity = 5000 kg wastewater/hr) that removes 90% of lead in the feed, which is then recycled back into the plant. Another stream from the unit is being released to a lagoon. If the stream leaving the plant has a rate greater than that of the treatment unit. the excess of the capacity of the unit (say. the excess above 5000 kg/hr) bypasses the unit. This excess is combined with the liquid leaving the treatment unit, which is released into the lagoon. The treatment plant releases 7500 kg/hr of wastewater. Determine the flow rate of the liquid to the waste lagoon. Include units. Express your answer in 1 decimal place only.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1) A heat exchanger is to be designed to heat 32/68 mixture of ethylene glycol and water from 24 ᵒC to 55 ᵒC by a hot water stream from 79 ᵒC to 42 ᵒC. Flow rate of cold stream is 20 kg/s. Inlet pressure for both stream is 50 psi and the maximum pressure drop of 10 psi for cold stream and 8 psi for hot water are permissible. Report valid assumptions made for the design and give required justification. Estimate Heat Transfer, Corrected LMTD, Tube bundle diameter (Using TEMA standards and Codes) and Tube cross sectional area Heat transfer coefficient Overall heat transfer coefficient Pressure Drop (Shell side & Tube Side)
A condenser of a steam power plant indicates a vacuum of 65 cm of Hg when barometer reads 75 cm Hg. The condensing steam has a temperature of 45 o C and a dryness fraction 0.9. Calculate: (i) the amount of air to be handled by the pump per min. if the rate of steam condensation is 2000 kg/hr. (ii) vacuum efficiency of the condenser.
5. A compressor receives CO2 with a pressure of 1 ATM and a temperature of 300 K. The compressor increases the enthalpy of the gas 1.5 times and decreases its volume 6 times. It is also known that during compression there is a heat loss of 32 J/kg. a. What is the work done by the equipment to compress 1 ton of gas? b. What is the final pressure of the gas? c. If the compressed gas is cooled to its initial temperature, what will its new pressure be?
Condition 1 PH = 17.0 PReg = 3.0 PR = 0.9 PR = 0.6 PL = 0.008 MPa, 1000°C MPa, MPa, 200°C MPa, 180°C MPa Required Net Power Output ? Thermal Efficiency?
Every closed feedwater heater generates a condensate. Determine:a) If it is sent to the high pressure line, what device (or machinethermal) is required to be used for this purpose.b) It would be required to install a mixing chamber. Why or for what?
The total volume of the water tank used in the equipment is 0.02 m3", and the water is heated through the heating rod. The efficiency of the water circulator 40W is 40%, and the remaining energy is released as heat. Given that the heat lost in the entire area in contact with the outside is KI(T-Ta)dT, find the following. O 25 °C → 30 °C. 2 30 °C → 35 °C (C.=4.184J/ml-C, Ta=20 °C. K = 10 J/s-C) (1) Energy balance: equation (2) Total energy used by Heating rod (J)
H2. A combustion facility is presumed to produce 9 Gigawatt-hours per year. Electricity price is 1.55 SEK per kWh. By raising the high temperature in the combustion facility från 373°C to 423°C to raise the efficiency. Calculate the repayment time for an investment of 1,730,000 SEK (operating cost staying the same). Assume that the facility is in a 12°C environment. (Clue: What expressions exist for the maximum thermal efficiency)
24 - The specific volume of the refrigerant R-134a entering an adiabatic emitter is 0.028371 m³/kg and 0.021786 m³/kg at the outlet. Ratio of outlet and inlet cross-sectional areas A2/A1=1.36 ; If the inlet velocity is 140 m/s and the flow is continuous, which of the following is the exit velocity of the refrigerant from the emitter? a) 165.6 m/s B) 60.4 m/s NS) 147.1 m/s D) 79.0 m/s TO) 64.7 m/s
4- y (=p g) for water at ambient temperature equals almost...........N/m³. a- 1000 b-62.4 c- 9.81 d-9810 5- y (=p g) for water at ambient temperature equals almost........... lb/ft³. a- 1000 b-62.4 C- 9.81 d-9810 6- y (=p g) for air at normal temperature and pressure is almost............ N/m³. b- 1000 b-62.4 c- 9.81 d-9810
Q3: The enthalpy of vaporization for water is: H,O H,0g sHvp =+ 44.0 kj/moie Calculate the AH for evaporating 3.00 grams of water and AH for Condensing 20 grams of water.
a.) Determine the mass flow rate of the water vapor, in kg/hr.b.) Calculate the volumetric flow rate of the water vapor leaving the plant, in m^3/hr.c.) Calculate the volumetric flow rate of the brine, in m^3/hr.