The motor inside a blender can be modeled as a resistance in series with an inductance, as shown in the given figure. Thewall socket source is modeled as an ideal 120 V rms voltage source in series with a 2-ohm output resistance. Assume thesource frequency is w = 377 rad/s.Given:R=11.1 ohm(+10)202www120 VFeWallsocketwwweleR2020 mlBlendermotorProblem 07.021.dWhat value of capacitor when placed in parallel with the motor will change the power factor seen by the voltage source to 0.9 lagging?(Round the final answer to two decimal places)The value of the capacitor that will change the power factor to 0.9 lagging isHF.

Answered: Image /qna-images/answer/246c0126-162a-4d41-acff-b100667b7b5c.jpg

wall socket source is modeled as an ideal 120 V rms voltage source in series with a 2-ohm output resistance. Assume the source frequency is w = 377 rad/s. Given: R=11.1 ohm 11+ 202 ww 120 V Wall socket Problem 07.021.d ww R 20 ml Blender motor What value of capacitor when placed in parallel with the motor will change the power factor seen by the voltage source to 0.9 lagging? (Round the final answer to two decimal places)

wall socket source is modeled as an ideal 120 V rms voltage source in series with a 2-ohm output resistance. Assume the source frequency is w = 377 rad/s. Given: R=11.1 ohm 11+ 202 ww 120 V Wall socket Problem 07.021.d ww R 20 ml Blender motor What value of capacitor when placed in parallel with the motor will change the power factor seen by the voltage source to 0.9 lagging? (Round the final answer to two decimal places)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three phase full controlled converter is supplied by a phase voltage VS=120V, 60 Hz. Consider a resistive load R=10 Q. If the RMS value of the output current is equal to 10.94A and the input Volt Ampere VA = 3125VA, then the output power Po and the power factor would be equal to: Select one: а. 3196.84W, 0.382 lagging b. 3196.84W, 0.772 lagging С. 1196.84W, 0.382 lagging d. 1196.84W, 0.772 lagging
??
Solve this question, no handwritten
A 240 kVA synchronous motor of rated apparent power consumes 95 kW of active power of the power grid. And it is possible to adjust it so that by working with this same active power, it compensates the power factor by providing reactive power (i.e., appearing with a capacitive component). How can you get this? What is the maximum reactive power that it can provide?
Exercise 1: Verification of Ohm’s law for a simple circuit across a Sinusoidal AC Supply Calculate the following: i. Current flowing through the resistor. (Irms) ii. Calculate the peak to peak voltage (Vpk-pk) and peak-peak current (I pk-pk) iii. Calculate the time period of the waveform
Q,..
FIND THE VALUES INDICATED AND SHOW THE COMPLETE SOLUTION. Peak RMS Average Phase Instantaneous Value Value Value Angle Value (e) ? 110 V ? 75° ? ? ? ? 15° 75.1 V
5- b) A factory has asynchronous motor loads with a power of 200 kW and a power factor of 0.8. When a synchronous motor with a power of 100 kW and a power factor of 0.909 is connected to this factory, what will be the new power factor of the system. Calculate the active and reactive power values in this case.
2. Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. a) What is the total VA of the combined load? b) What is the overall PF of the combined load? c) What RMS voltage is the combined load operating? d) What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? e) What is its approximate capacitance in microfarad?
One phase of a 3-phase alternator consist of 12 coils in series. Each coil has an rms voltage of 10Vinduced in it and the coils are arranged in slots so that there is a successive phase displacement of10 electrical degrees between the emf in each coil an the next. Find by calculation the rms value ofthe total phase voltage developed by the winding. If the alternator has six pole and is driven at 100rpm.