w1 kN/m w1 w2 w3 X y X (x+3) m 3 kN/m 12 kN/m 12 kN/m 7 10 m m w2 kN/m y w3 kN/m Determine the following: ANSWERS IN ABSOLUTE VALUE AND IN THREE (3) DECIMAL PLACES • Resultant Force along vertical axis/line = Resultant Force along horizontal axis/line = • The Resultant Force = • The angle of the Resultant Force with respect to vertical axis/line = kN kN KN deg

w1 kN/m w1 w2 w3 X y X (x+3) m 3 kN/m 12 kN/m 12 kN/m 7 10 m m w2 kN/m y w3 kN/m Determine the following: ANSWERS IN ABSOLUTE VALUE AND IN THREE (3) DECIMAL PLACES • Resultant Force along vertical axis/line = Resultant Force along horizontal axis/line = • The Resultant Force = • The angle of the Resultant Force with respect to vertical axis/line = kN kN KN deg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam, 100 mm wide by 270 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 80 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A beam shown in Figure 7.7 is made of T beam, determine maximum shearing stress develop due to various type of loading. w- 3kN/m A B 2.0m 2.0m 2.0m
Calculate the true strain when the initial length 10.5 mm and the final length *12mm 0.143 O 0.134 O 0.413 O 0.314
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 80mm and a wall thickness of 6mm. Determine the normal stress in each truss member. 1.0 m 1.5 m B 3.3 m 15 KN 12 kN 90 kip
Problem 2: Analyze the following, state the determinacy and the stability. 3. 2. - hinge hinge hinge-
A closely coiled helical spring made of 10mm diameter steel wire has 15 coils of 100mm mean diameter. The spring is subjected to an axial load of 100 N. For a modulus of rigidity of 8.16×104 N/mm², find the stiffness of the spring.
A wooden beam 100 mm by 200 mm , supported as shown in figure below, carries a load F. what is the largest safe value of F if the maximum stress is not exceed 10 MPa ? 100mm 200 mm
A steel marine propeller shaft transmits a power of 5 MW at a frequency of 2.5 Hz. The diameter of the shaft is 250 mm with G = 83 GN/ m². Determine the maximum shearing stress in the shaft.
A solid circular steel column is 3 m long and 0.4 m in diameter. It carries a load of 50 MN. The modulus of clasticity is 200 GPa. (i) Find the stress in the column. (ii) Find the strain in the column.
A simple pin-connected truss is loaded and supported as shown in the figure shown. All members of the truss are aluminum pipes that have an outside diameter of 60 mm and a wall thickness of 4 mm. Determine the normal stress in truss AC in MPa. 1.5 m O 62.5 63.9 O 71.2 66.4 1.0 m B 3.3 m 15 kN 12 kN
A cantilever beam, 80 mm wide by 220 mm high and 7 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Determine the magnitude of the stress in a fiber 90 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
A cylindrical pressure vessel is 1200 mm in diameter. It is made of rolled mild steel plate. The vessel is subjected to an internal pressure of 2 N/mm². If the material yields at 200 N/mm², what should be the minimum safe thickness of the plate, based on Maximum Principal Stress Theory?