A tie bar (20 mm × 10 mm) carries a tensile load of 1 kN as shown in the figure. Under this load, the maximum intensity of stress over the mean value will increased by 20 mm 10 mm — my je wy #24824-0 3 S 1 mm

A tie bar (20 mm × 10 mm) carries a tensile load of 1 kN as shown in the figure. Under this load, the maximum intensity of stress over the mean value will increased by 20 mm 10 mm — my je wy #24824-0 3 S 1 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Axial Load, P(kN) A 2 m long axially loaded mild steel rod of 8 mm diameter exhibits the…

Q: Given: A steel rod (A= 150 mm²) is stretched between two fixed points with a tensile load of 5000 N…

Q: A stepped steel shaft shown below is subjected to 10 N-m torque. If the modulus of rigidity is 80…

A: Given: A stepped steel shaft is given,Torque applied, T=10 N-mmodulus of rigidity, G=80 GPa

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

Q: Consider a 200 mm dia solid rod having yield stress in shear as 300 N/mm². Calculate the radius of…

Q: R, RD

A: Given: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm.…

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

A: Given, Diameter of cylinder = 30 cm Thickness of steel band = 8 mm Internal diameter of the hoop…

Q: A steel [E = 29900 ksi, a = 6.5×10-6/°F] bar is held between two rigid supports. The bar is is then…

Q: An elastomeric bearing pad consisting of twosteel plates bonded to a chloroprene elastomer…

A: Solution: Given: a = 125 mm b = 240 mm t = 50 mm V = 12 kN d = 8.0 mm

Q: The inner and outer diameters of a hollow cylindrical steel are 10mm and 15mm, respectively. It is 1…

Q: A compound bar, 1.5m long is made up of three concentric square components A, B and C, fitted…

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

Q: Calculate the tensile stress when applied force of 1200ON on specimen of diameter of 7mm

A: tensile stress = tesile force / normal cross section area

Q: A 220 mm? steel rod and 420 mm? copper rod supports a rigid bar as shown. If a 30 kN load is…

Q: 25 KN III a a ASTEEL ACOPPER STEEL 2.8 m 3.6 m hree vertical rods of equal distance, each has a…

A: Data given:Length of 2 steel rods = 3.6mLength of copper rod = 2.8mDiameter =…

Q: For the continuous beam shown in Figure 1, draw the internal force diagrams. You must accompany your…

A: Given Data:

Q: A circular tube of aluminum is subjected totorsion by torques T applied at the ends (see figure).The…

Q: HW A nigid Slab weighing 6o0 Kw is Placed uPon two bronze vads and one Steel Vocd eanch of bo00 mm?…

Q: A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What…

A: Given: The diameter of the pulley is 6 in. The diameter of the shaft is 2 in. The power transmits is…

Q: The Shape Factor Fcs The Shape Factor Fqs The Shape Factor Fs : The Depth Factor Fqd : The Depth…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure P-108.…

A: Given data in question Area Stresses Loads To find out Maximum value of P so that stresses should…

Q: need the answer quickly

Q: At an axial load of 24 kN, a 40-mm-wide by 20-mm-thick polyimide polymer bar elongates 2.7 mm while…

Q: Problem 6. Solve the average normal stress occurring in each steel wire shown in the figure. Assume…

Q: A 2 m long, axially loaded mild steel rod of 8 mm diameter exhibits the load- 14000 12000…

A: A graph of displacement against load, yield stress, length of mild steel rod, Diameter have been…

Q: A unitorm bar 1 is connected to a tapered rod 2. Both are subjected to adal loads as shown. IfP- 7…

Q: For a metal rod of 12 mm diameter and 22 cm length; a) When exposed to a load 2000 kg, it elongated…

A: Finding out true stress and strain and Poisson ratio.

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…

Q: Crack FIGURE 0xx . . COS 2.7 03, COS 27 K₁ ossin(cos() ਰ - X Stresses near the tip of a crack in an…

Q: Determine the stresses in the steel rod and copper tube if the temperature rises from 15 C° to 70…

Q: A rigid platform in Figure MEC - 208 has negligible mass carries a center load P and rest two…

A: Calculate the stress in each aluminum bar?

Q: A wire of 3 mm diameter is bent into a circle and held with its ends and just in contact. If the…

A: A copper wire with a diameter of 3 mm is bent into a circle and held with its ends just touching.The…

Q: In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in…

A: Given DataDiameter of the specimen=0.505 inGauge length=2 inTotal length=8 inYield strength=80000…

Q: Determine the absolute maximum shear stress developed in the beam Express your answer to three…

A: Given : Rectangular cross-section b = 3 in d = 6 in For the given loading in the beam, maximum…

Concept explainers

Planar Stresses

Question

A tie bar (20 mm x 10 mm) carries a tensile load
of 1 kN as shown in the figure. Under this load,
the maximum intensity of stress over the mean
value will increased by
20 mm
10 mm
wwwww
↓
1 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Required given information

VIEW

Step 2: Calculate the maximum intensity of stress over the mean value increased by

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A copper rod of length L = 18.0 in. is to betwisted by torques T (see figure) until the angle ofrotation between the ends of the rod is 3.08.(a) If the allowable shear strain in the copper is0.0006 rad, what is the maximum permissiblediameter of the rod?(b) If the rod diameter is 0.5 in., what is theminimum permissible length of the rod?
I need the answer as soon as possible
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in the figure. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm 70.72 mm 14 150 mm 150 mm ► 60 mm dia 150 mm
Solve with correct solution
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown below. Axial loads are applied at the positions indicated. Find the maximum value of P in Newton that will not exceed a stress in steel of 150 MPa, in aluminum of 87 MPa, or in bronze of 97 MPa.
solve thee following problem with the correct answer please, please make sure to show so I can understand.
A rigid bar of negligible weight is supported and loaded with 70 kN, compute the temperature change AT (°C) that will cause the stress in the bronze rod (L = 1.5 m, A = 300 mm?, and E = 83 GPa) to be 50 MPa. Assume a = 18.9 µm/(m°C) for bronze and 12.8 um/(m°C) for aluminum (L = 3 m, A = 750 mm2, and E = 70 GPa). Aluminum Bronze 2.5 m 1.5 m 70 kN
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
pls help me. thank u refer to the picture attached below.