w B m -2 m- -2 m- For the beam and loading shown, (a) the absolute value of the reaction force at B|R 8| In kN units, (b) the absolute value of the displacement at the midpoint D of part BC of the beam |y o| Specify in mm units. Take the P value of 11 kN and the w value of 33 kN/m in the question Take E = 200 G Pa and I = 34.4 x 10 -6 m 4

w B m -2 m- -2 m- For the beam and loading shown, (a) the absolute value of the reaction force at B|R 8| In kN units, (b) the absolute value of the displacement at the midpoint D of part BC of the beam |y o| Specify in mm units. Take the P value of 11 kN and the w value of 33 kN/m in the question Take E = 200 G Pa and I = 34.4 x 10 -6 m 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the force method to find the value of the redundant force RCx. All bar areas are the same. (Ans: RCx = 15.71 k) A B 30 ft· D 60 k 30 ft [T] E 0x00 20 ft
Determine the change in length, breadthand long,semm thickness f a steel bar which is 4 m wide and 20 mm thick and is subjected to axial pull of KN in the divechion of leng th. E = 2xlo/m, = 0.3
Please answer the ff in a complete solution and draw fbdQuestion: Solve the problem using the conjugate beam method. EI is constant
Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending moment diagram for the beam (by using the singularity- Macaulay's equation) 2- Determine the maximum bending stress in the section (square section with side length of 40cm)
Q.2) A simple beam of span length 3.2 m carries a uniform load of intensity 48 kN/m. The cross section of the beam is a hollow with wood flanges and steel side plates, as shown in the figure below. The wood flanges (E = 10 GPa) are 75 mm by 100 mm in cross section, and the steel plates (E = 210 GPa) are 300 mm deep. What is the required thickness t of the steel plates if the allowable stresses are 120 MPa for the steel and 6.5 MPa for the wood? 75 mm 75 mm C 100 mm 300 mm
Using virtual work method, find: (a) the real internal force F in member BF in kN (b) real internal force F in member GH in kN (c) virtual internal force Fv in member HG due to a one unit horizontal load applied at joint G (d) virtual internal force Fv in member CD due to a one unit horizontal load applied at joint G (e) horizontal displacement at joint G due to the applied loads in mm.
For the beam shown, calculate reactions and draw the shear force and bending moment diagrams. Schematically draw the deformed beam. Notice that at point e there is a zero moment joint.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1760 in.4]. For the loading shown, determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 200 kip·ft, P = 30 kips, LAB = 3.3 ft, LBC = 5 ft.
By using Muller Breslau’s Principle and the prismatic beam shown in Figure Q1 below, draw quantitative influence lines for the: (a) Vertical reactions at B,(b) Bending moment at point C and(c) Shear force at point C
The cross-section and loading condition of a simply supported beam is shown in figure. The allowable compression and tension stresses of the material are Ocomp.allow = 100 MPa and Otens allow = 120 MPa, respectively. в 2m 2m 2m' a) Draw the internal bending moment diagram of the beam 5cm b) Calculate the largest load q that can be safely supported by beam. 15cm 5cm c) By using the q value that you calculated in (b) section, sketch the normal stress distribution diagram of the cross-section. 20cm y Note: Neglect the shear effect.
Please write the solution on paper.
(a) Compute the reaction at support B of the beam shown below using the force method. (b) Compute the vertical displacement at point C in terms of EI. (Hint: The equation in the box below can be used to compute any needed displacements). A 4 m 30 kN L -b. 4 m B 3 m 20 kN 6 с Displacement, A (upward positive): Pbx 6LEI 0 < x