Vout Given that : R = 200 2, V = 13 V, I₁ = 16 mA, Z₂ = 102, Izk a) Determine V at Izk and at IZM OUT ZK = 1 mA, P = 1 W. b) Determine the minimum value of load resistor R₁ that can be connected to the circuit output, and then, calculate the load regulation + VIN 30 V H R w

Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above. (Assume necessary data) a. The output voltage is 12 V, the output power is 540W b. The output voltage is 12 V, the output power is 54W c. The output voltage is 12 V, the output power is 5.4W d. The output voltage is 24 V, the output power is 2.25W

A 75-V DC voltage source is coupled to a 25 kOhm load resistor through a 35 kOhm source resistance. A Voltmeter-A has a sensitivity 8 kOhm/V with a measuring range of 0-35V. Calculate error in the voltmeter reading expressed in a percentage of the true value.

Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?

Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. Choose the correct statement for the above PV Module. (Assume necessary data)      a. The output voltage is 0.5 V, the output power is 12W b. The output voltage is 2 V, the output power is 12W  c. The output voltage is 12 V, the output power is 6W  d. The output voltage is 0.5 V, the output power is 6W

Q1: For the circuits shown in figures. If the temperature has changed from 25°C to 65°C, find Alc. Ic=1.5mA at 25°C, Rf 250k2, Rc=1k and Re-0.5k2. 25°C 65°C +Vcc 55 70 Rf Rc Ico InA 16nA VBE 0.6 0.5 Re

Given that IE1 = IC1 and VBE = 0.7V, do the circuit analysis shown in the figure, and determine: VCE1 = ? IC1 = ? VCE2 = ? IC2 = ?

Construct a forward bias diode circuit in multi-sim (desktop, not live). Simulate and find the current through the resistor and the voltage across the resistor.

Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si

1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…