voltage of the p-n-junction and is defined by ↓ V₁ kT qe V↓↓ where ↓ k is Boltzmann constant, k =1.381×10-23 J/K T is the absolute temperature in degrees K q, is the charge of an electron, q, = 1.602×10-¹⁹ C ↓ Note that the unit fork is joules, so the unit for Vis energy per unit charge or volts. Intuitively, it is the average potential caused by the thermal motion of electrons. a) Calculate the value of the thermal voltage (in millivolts) when the temperature is 50 °C. b) For this diode, use Shockley's diode equation to calculate the diode current In (in microamps). using if Is = 40 mA, n-2 (low value of VD), and the applied bias voltage Vis 0.5.V.

voltage of the p-n-junction and is defined by ↓ V₁ kT qe V↓↓ where ↓ k is Boltzmann constant, k =1.381×10-23 J/K T is the absolute temperature in degrees K q, is the charge of an electron, q, = 1.602×10-¹⁹ C ↓ Note that the unit fork is joules, so the unit for Vis energy per unit charge or volts. Intuitively, it is the average potential caused by the thermal motion of electrons. a) Calculate the value of the thermal voltage (in millivolts) when the temperature is 50 °C. b) For this diode, use Shockley's diode equation to calculate the diode current In (in microamps). using if Is = 40 mA, n-2 (low value of VD), and the applied bias voltage Vis 0.5.V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

please include full solutions!!! will give thumbs up if answer has complete solution.pleas
1. You are to design a diode clipper circuit that will keep high voltage spikes from a 'noisy power supply from reaching sensitive electronics. A conventional silicon diode is used as part of the design. The clipper circuit is to be designed so that voltages 2 Resistor 10 volts are 'clipped'. SI Diode Vin from noisy Vout to electronics a) What would a suitable Zener breakdown voltage be? source Zener Diode b) From the manufacturer's specifications sheet, what would be a good choice for the Zener diode (i.e. what part number? 1Nxxx)? Why? c) If you want to 'clip' voltages that are s-10 volts as well, show how you would modify the circuit.
Consider three p -n-junctions as shown below. Say true or false. Write a sentence justifying your answer. A B Np=1015 cm3 Np=1017 cm3 Np=1015 cm cm P+ a. Both diodes A and C will have the same reverse saturation current if they are ideal. b. Assuming that the diodes are all ideal, diode B will have the lowest reverse saturation current. c. Assuming that the diodes are non-ideal, diode C will have the highest reverse saturation current.
1. The full-wave controlled bridge rectifier shown has an ac input of 120 Vrms at 60 Hz and a 52 load resistor. The delay angle is 30°. Determine the average current in the load, the power absorbed by the load and the source voltamperes. V₁ I sin cor H www + Vo
Q 5. Find the values of I and V in the circuits shown in Figure. Assume Ideal SI Diode.
Please answer in short like it definitely don't reject in shorts please.. Thanks.. Please Asap
QUESTION 3 A half-wave, diode rectifier circuit with a 1 kilo-ohm load operates from a 110-V (rms) 60-Hz household supply through a 10-to-1 step-down transformer. Assuming ideal an diode, the average load voltage is nearly O 5 V O 110 V O 11 V O 10 V
need help with d and e
Can you solve this question by explaining your solution step by step and giving details on the formulas and calculations, please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)
2. Explain which of the following instructions are invalid? State the invalidation reason and give the correct form for invalid instructions: a. MOV DL,AX b. MOV ES,CX c. MOV [BX],[2000] d. MOV BX,[AX] e. MOV CL,[BL+200] f. MOV 1234,DX g. MOV CH,[BX+SI+300] h. MOV DS,[SI+DI-5] i. MOV [4500],1234 j. MOV 200,[300]
?
Since the reverse (saturation) current passing through a p-n junction with an ideality factor of 1 at 32°C is 50 nA; What is the current in the right direction at a voltage of 0.5 V applied in the right (conduct) direction (feed forward)?