Vodafone decides to use a digital TDMA scheme which can tolerate a Signal-to-Interference Ratio of 17dB in the worst case. Find the optimal value of the path lost exponent, y for an omnidirectional antenna; assuming i=3 and j=2. Assume that there are six co-channel cells in the first tier, and all of them are at same distance from the mobile. Use suitable approximations.

Vodafone decides to use a digital TDMA scheme which can tolerate a Signal-to-Interference Ratio of 17dB in the worst case. Find the optimal value of the path lost exponent, y for an omnidirectional antenna; assuming i=3 and j=2. Assume that there are six co-channel cells in the first tier, and all of them are at same distance from the mobile. Use suitable approximations.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

hi solve 1,2,3
Problem 1 For the following network determine the values of IDI, ID2, and Vo. E = 10V Si -M- +ID GaAs ID2 Vo R= 5 kr ...ts
Computer Science In a wireless system, PRX = –99 dBm. Find the theoretical maximum spectral efficiency if B = 1 MHz, F (noise figure) = 8 dB, k (Boltzmann constant) = 1.38x10-23 joule/oK, and T = 22 oC.
The measured output voltage of a cable is 7mv, for an input voltage of 15mv and the near end cross talk ratio (NEXT) of the cable is 20dB. Find attenuation and attenuation to cross talk ratio (ACR) of the cable.
We would like to design a bandpass filter in a DSP system which attenuates a signal outside the range of frequencies from 1000 Hz to 2000 Hz with near unity gain within the passband. The maximum bandwidth for any input signal is below 5000 Hz. (a) What is the minimum sampling rate f, that should be used for this DSP system? (b) With a sampling rate equal to fs, start by designing a corresponding lowpass filter, using a rectangular window of length 60. Note that you will afterwards transform this lowpass filter into the required bandpass filter, so choose the parameters accordingly. Write the expression for the impulse response hLP[n] of this filter. (c) Find the impulse response hep[n] of the bandpass filter by transforming the appropriate lowpass filter from part (b). Note: Be careful when applying equations from Slide 20.11. The derivation on Slide 20.11 assumed no "delay" to make the filter causal. If your resulting hap[n] is not symmetric, then you have not applied the delay…
q10-
Imagine the length of a cable is 2500 metres. If the speed of propagation in a thick co-axial cable is 60% of the speed of light, how long does it take for a bit to travel from the beginning to the end of the cable? Ignore any propagation delay in the equipment. (Speed of light c = 3 x 108 metres / sec)
Synchronous and asynchronous transmission (presentation, comparison). Considering a baseband signal with the bandwidth between 210 kHz and 3970 kHz modulating the amplitude of a 54 MHz sine carrier, determine the frequency range of the resulted amplitude modulated (AM) signal. Polynomial block codes for data communications (principle, polynomial description). What is the ratio between the data rates (D₁/D2) of two transmitted signals occupying the same bandwidth, but different number of levels, i.e., M₁ 8 and M₂ = 32, using Raised Cosine characteristics with the roll-off factors a₁ = 0.5 and a2 = 0.25, respectively?
Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the intended capacity is 8 Mbps. a. What should be the signal-to-noise ratio (SNR) to obtain this capacity? Constant values= c=3x^10°m/s, k=1,38x^10231/K I
The Amplitude Modulation (AM) is a technique used in communication for transmitting information via radio carrier wave. AM works by varying the amplitude of the transmitted signal in relation to the information being sent. The equations of the carrier signal, the original signal to send, and the modulated signal combining the two signals are respectively: VI-V sin (2πƒct) V2=Vm sin (2πfmt) V3=Vcsin (2πfct)+ Vm sin (2πfmt)* sin (2nfct) C Supposing that Vc =Vm=1, fc-20, fm=1. Write a MATLAB program that plots the three signals with single call, the graphs must be contain (desired title, axis labels, annotations, with symbols for color, style, and marker) for each graph. Use the step 0.0025 for the time.
Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem5. An access multiplexer (AM) installed in the roadside box of the NBN (National Broadband Network). Assume that 200 homes are connected to the AM. The average packet interarrival arrival time at the AM is 200 μs. The average packet length is 2,500 bytes where the packet length is exponentially distributed.a. Calculate the number of packets arriving at the AM every hour.b. Calculate the incoming traffic rate (in bits/sec) at the input of the AM.c. Assume that the output of the AM is connected to the NBN core network via a 2-Gbps link. Calculate the total normalised load ρ at the AM.d. Assume that the packet arrival process is exponentially distributed. Calculate the average queuing delay introduced by the AM.
Consider a channel with bandwidth B = 2Mhz and a signal to noise ratio of 40dB (expressed in log scale, remember the conversion!). What is the maximum data rate achievable? Explicitly mention the theorem and the calculation that lead to the solution.