vind speed of 8 m/s, a rotor diameter of 37.5 m, a fixed rotor rotational speed of 40 r/min, and a generator rotational speed of 1800 r/min. a) What is the tip speed ratio at rated wind speed? b) What is the tip speed ratio at cut-in? c) What is the overall efficiency of the turbine, drive train, and generator if Pe = 100 kW when the wind =peed is 8 m/s? Assume standard conditions.

vind speed of 8 m/s, a rotor diameter of 37.5 m, a fixed rotor rotational speed of 40 r/min, and a generator rotational speed of 1800 r/min. a) What is the tip speed ratio at rated wind speed? b) What is the tip speed ratio at cut-in? c) What is the overall efficiency of the turbine, drive train, and generator if Pe = 100 kW when the wind =peed is 8 m/s? Assume standard conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wind generator rotates at 17 rpm on the rotor (the part with the blades). It is a direct drive (meaning the rotor connects directly to the generator). The generator is 86% efficient and produces 3.1 MW. What is the torque on the rotor?
P4.22). A single-cylinder four-stroke-cycle spark-ignition engine operating at 3500 rpm has a brake mean effective pressure of 1800 kPa and a displacement of 400 cm'. Atmospheric conditions are 101 kPa and 27°C. a) If the stroke is 6 cm, what is the bore? b) What is the brake power? c) If the mass air-fuel ratio is 16 and the fuel flow rate is 0.00065 kg/s, what is the volumetric efficiency? d) Compare your results with the performance of a two-cylinder engine with the same overal l geometric characteristics.
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW Find the Volumetric efficiency
26 - In the simple ideal Rankine cycle, water enters the pump in saturated liquid phase at 50 kPa and leaves the pump at 6600 kPa. What is the power of the pump for 36 kg/s flow rate? a) 242.9 kW B) 259.1 kW NS) 257.6 kW D) 199.7 kW TO) 200.4 kW
Question 3 (i) What information is needed to make an accurate estimate of the annual energy capture for a wind turbine? List at least two control mechanisms available in modern wind turbines, which respond to variations of wind speed and direction?
Approximate the theoretical power in wind moving at a speed of 6 m/s with an air temperature of 40°F striking wind turbine with a 5 ft diameter rotor (use mass density = 1.277 kg/m3). a.2,707.97 W b.75.22 W c.251.57 W d.None of these e.6.99 W
7.) A Rankine cycle is used for a steam power plant. Liquid first enters the turbine at 2.25 MPa and 300C then exits at 0.025 MPa. The pump receives saturated liquid from the condenser before sending it to the boiler at the original pressure. a.) Draw the T-S diagram. b.) Find the dryness at turbine exit, c.) Wp, d.) Qa, e.) Qr, f.) Wt, g.) Wnet (kJ/kg), h.) Efficiency (%), and i.) Steam rate (kg/KVWH) 100%, 3.12 kJ/kg, 3016.3 kJ/kg, 2346.3 kJ/kg, 522.3 kJ/kg, 35.22%, 4.63 kg/kWh • 95.21%, 2.27 kJ/kg, 2809.6 kJ/kg, 1875.21 kJ/kg, 815.33 kJ/kg, 31.29%, 3.51 kg/kWh 83.73%, 2.27 kJ/kg, 2742.1 kJ/kg, 1964.48 kJ/kg, 779.89 kJ/kg, 28.36%, 4.63 kg/kWh 100%, 0 kJ/kg, 3016.3 kJ/kg, 271.93 kJ/kg, 2798 kJ/kg, 100%, 1 kg/kWh
A regenerating brayton cycle that uses air as the fluid has a pressure ratio of 7. The minimum and maximum temperatures in the cycle are 30 ° C and 890 ° C. assuming an efficiency of 72% for the compressor, 82% for the turbine and an effectiveness of 62% for the regenerator. determine: a) the turbine air outlet temperature b) net labor output c) the thermal efficiency of the cycle
2) Determine the Ranking Cycle Efficiency in %. 3) Determine the Brake Thermal Efficiency of the cycle in % 4) Determine the Combined thermal and electrical efficiency in %.
Projects 3: Gas turbine operated on Brayton cycle Gas turbine operated on Brayton cycle used for electric utility as separated or combined cycles with steam power plant. Broadly speaking, gas turbine cycle is preferred over steam power plant in power station. Therefore, your head of department asked you to investigate and study the possibility of upgrading the power plant in Project-1 to a gas turbine cycle or a combination of both. However, your head of department asked to deliver a report showing you professional evaluation and assessment for gas turbine cycle efficiency. This report will be used to convince the company board committee. Task.1 Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications: A pressure ratio of 14.77. The gas temperature is 350 K at the compressor inlet and 1500 K at the turbine inlet. Under the assumption of standard air, perform the following: 1. Gas…
A diesel engine operates on a diesel cycle based on standard air acceptance. The compression ratio of this diesel engine is 18, the compression process starting temperature is 300 K and the pressure is 0.1 MPa, the shear rate is 2. According to this; A) Draw the Pv, Ts diagram of the cycle.B) Calculate the pressures and temperatures at the end of each cycle of the cycle.C) Find the thermal efficiency and the average effective pressure of the cycle.