7.) A Rankine cycle is used for a steam power plant. Liquid first enters the turbine at 2.25 MPa and 300C then exits at 0.025 MPa. The pump receives saturated liquid from the condenser before sending it to the boiler at the original pressure. a.) Draw the T-S diagram. b.) Find the dryness at turbine exit, c.) Wp, d.) Qa, e.) Qr, f.) Wt, g.) Wnet (kJ/kg), h.) Efficiency (%), and i.) Steam rate (kg/kWh)

7.) A Rankine cycle is used for a steam power plant. Liquid first enters the turbine at 2.25 MPa and 300C then exits at 0.025 MPa. The pump receives saturated liquid from the condenser before sending it to the boiler at the original pressure. a.) Draw the T-S diagram. b.) Find the dryness at turbine exit, c.) Wp, d.) Qa, e.) Qr, f.) Wt, g.) Wnet (kJ/kg), h.) Efficiency (%), and i.) Steam rate (kg/kWh)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

O Enthalpy data is given for a regenerative Brayton cycle with intercooling and reheating. The cycle produces a net power of 14MW. Calculate a) the mass flow rate of air in kg/s b) heat rejection rate of the intercooler in kW c) the back work ratio d) the thermal efficiency e) the second law efficiency if the cycle receives heat from a medium at a temperature of 1600K and rejects heat to a medium at a temperature 290K.« State h (kJ/kg) State h (kJ/kg) 300.19 1 6 1575.57 2 411.22 7 1085.31 3 300.19 8 1575.57 4 446.50 9. 1173.84 1173.84 10 446.50 Regenerator Reheater Combustion chamber Compressor Compressor II Turbine I Turbine II Intercooler
In an ideal open feedwater heater Rankine cycle, water leaves the condenser at 100 kPa and from the boiler at 500 *C and 3 MPa pressure. The water emerges as a saturated liquid at 400 kPa pressure from the open feed water shown in the figure. According to this; a) Show the cycle in a T-s diagram with saturated liquid and saturated vapor curves. b) Find the total pump work (kJ/kg). c) Find the ratio (y) of the mass of steam leaving to heat the turbine feedwater to the mass of steam entering the high pressure turbine.
Use the bled steam to solve the question, please (FULL SOLUTION)
Answer letters D, E, F
H.W2:-A) The bore and stroke of an internal combustion engine working on Otto cycle are (17 cm) and (30 cm) respectively. If the total volume is (8.825 cm3),find the air standard efficiency. Take X=1.4
No.1 only
1. (pp11-1p150gutay) -The steam supplied to an engine is at 198 N/m² superheated to an engine 300 C. The exhaust pressure is 1.37 N/m². a) Find the theoretical amount of work per kg of steam if the engine works on the Rankine Cycle. b) What would be the steam consumption per HP of an engine working between the above conditions of steam supply and exhaust, and having a relative efficiency of 70 % based on the Rankine cycle.
Give neat solution in text.
please i need complete solution of all parts with detail and step by step thanks
In an ideal Brayton cycle with maximum and minimum temperatures of 1600 K and 290 K, air enters the compressor at 100 kPa. Since the pressure ratio is 15: a) Cycle heat intake, b) Net work, c) Find the yield. Features for air: k=1,4, R=0,287 kJ/kg K, cp=1,005 kJ/kg K
Task.2 Describe the operation of heat-pump cycle (optimal case only) in Figure.2 and the its themodynamics properties, by constructing a P-h and T-S plots showing the following: a) The processes and indicate their types (isothermal, isobaric or isentropic) b) The refrigeration effect (RE), heat of compression (HOC), and heat of rejection (HOR).
5.) An ideal Reheat Cycle has a turbine inlet pressure of 10 MPa with steam temperature of 400C. The steam expands to 5 MPa then it is reheated to 400C. After expanding in the 2nd turbine, the steam enters the condenser at 7 kPa. Draw the TS diagram, find the cycle efficiency and steam rate.