Vi • • + Vs www IV = 1000-0°Ꮴ W = 20rad/s 10:1 + R1 = 10000 ли R₂ = 100 Vp Vs Is Find primary voltage and current. Find secondary voltage and current. • What is the phase angle? • What is the power factor? • Calculate the complex power, reactance power and real power. L₁ = 1H

Q: Question 17 On Arduino Uno we can use the ________ command to do pulse width modulation:…

A:

Q: Suppose you have measured a time delay of 70 microseconds between the two cursors below. The signals…

A: In this question We need to determine the angle between both signals in degree.  We know Frequency…

Q: The following ASCII code 0000110 represents

A:

Q: Approximately, what is the percent jitter for the following signal? 0.012 0.005 0.011 0.01 主

A: Jitter is a plot which is used to show the value distribution which are very consolidated. It gives…

Q: The main difference between a register and a counter is

A: ans:(d) register has no specific sequence of states

Q: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

A: In a/an __________ measurement the ultrasonic level sensor's analog output gets smaller as the waves…

Q: Consider a 8-bit ADC and full scale voltage measurement range of (-29 to 29).The Resolution  will be…

A:

Q: In control system, the input signal is generally represented as

A:

Q: The first element in any measuring system is the O variable conversion element signal processing…

A: Measurement of any quantity is the comparison of the measured value with a pre defined standard.…

Q: Show all the base-10 digits 0-9 on a 7 segment display.

A: The solid state optic PN junction diode known as an LED, or light-emitting diode, produces light…

Q: Draw Full Adder By Using 3 Line-8 Line Decoder. 1 Add file

A: STANDARD SUM OF PRODUCT FORM: In standard SOP form, the function is the sum of a number of product…

Q: Differentiate between absolute instruments and secondary instruments

A: Different between absolute instruments and secondary instruments:   Absolute instruments…

Q: Enter the correct value (either 1 or 0) in each box; consider each row carefully before deciding on…

A:

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: What is a multiplexer? How many outputs does a multiplexer have? Insert the symbol of a 4 to 1

A: The explanation is as follows.

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: draw truth table and waveform, make sure its correct please

A: The state table can be analysed by verifying state of each flipflop after each clock.

Q: Question 10 00 answer. The following shift-register based sequential system detects the following…

A: Giventhe shift register base sequence system detects  sequence 0001,0011,0101,0111

Q: multiplexer contains. multiplexer contains.... select lines 4-1 4 O 20 8 O select lines 16-1 4 O 8 5…

A: In this question we need to choose a correct option

Q: Q what is clocking block and intial block

A: Final block is executed after $finish. Final block doesn't have delay statement.Module is a block a…

Q: OLU The state diagram for a negative edge triggered counter is chown below. Sketch the corresponding…

A: Since the counter is counting to the number 15, the required number of the flip-flop will be four to…

Q: art 4. Two Bit Wide 4 x 1 Multiplexer sing process INPUT_A INPUT_B OUTPUT_Y INPUT_C INPUT_D…

A:

Q: 6- What is the difference between Software and Hardware interrupts?

A: Difference between Software and Hardware interrupts ?

Q: Do Y. So EN Parity generator Demultiplexer Decodor 身

A:

Q: How do you clear a new EPROM?

A: We need to tell about how do we clear a new EPROM.

Q: What is the accuracy of bellow sensor? O a. ± 1% O b. ± 0.001% O c. ± 0.1% O d. ± 0.01%

A: At high differential pressures the accuracy is around 1.5% of the measuring range.  and At lower…

Q: The carrier signal is always an analog signal. an analog signal in case of an analog information…

A:

Q: The regiater length is 4 bits and initially it contains 1001. Shift the register to the right six…

A:

Q: The voltage Vc(t) (in V) and the current i(t) (in Amp) after closing the switch in the circuit shown…

A: MATLAB Code: R=2000; C=3000e-6; v_int=30; time_cons=R*C; t=1:1:40% declaring time period from 1 to…

Q: In control system, the output  signal is generally represented as

A:

Q: The following circuit is a Modulus 14 counter. If we disconnect the input connection to the AND gate…

A: Right Answer option 11

Q: In an estable multivibrator using a 555 timer, the out put is and the high or logic (1) when the the…

A: Astable multivibrator using 555 timer : An Astable multivibrator using 555 timer is act like a…

Q: For a 10-bit digital ramp ADC using 500 kHz clock, the maximum conversion time is 1. 2048 μsec 2.…

A: Number of bits n=10, Frequency of the clock f=500 kHz.

Q: An RLC circuit has a bandwidth of 40 kHz and a Q-factor of 10. Its resonant frequency is

A: Band width of RLC circuit is B.w= 40 kHz Q factor Q = 10 Resonant frequency  Fr = ?