Show all the base-10 digits 0-9 on a 7 segment display.

Q: Use four 1-bitAlu to create a 4-bitAlu. with three control signals: Bnegate (1), Operation (2),…

A: The diagram shows how a 4-bit ALU  can be designed by using four 1-bit ALU.

Q: 3. In the astable timer in the following figure in order to get duty cycle = %30 and F = 200Hz from…

A:

Q: Q4/ design logic counter up-down of (1, 2, 5, 8, 9, 10, 12, 14, and 15)

A: Here it is asked to design an up counter where the counting states are given. Here asynchronous…

Q: is the most important segment and it contains the actual assembly language instructions to be…

A: microprocessor works based on the assembly lenguage instruction provided to it.

Q: 36. An SRAM has address lines from A to A₁, and data width from Do to D₁5. Total capacity of the…

A: It is given that:Number of address lines=20 Number of data lines= 16

Q: Perform the following operations as indicated and check the results in the decimal system Note…

A:

Q: When using signed integers and in a 4-bit cell, the decimal number -7  can be be represented in…

A: In the signed bit representation of binary numbers, the MSB(most significant bit )shows the sign of…

Q: . register or registers can be used for input and output purpose O DX O BX O cx O no one AX

A: AX comes under the category of the primary accumulator. It is used as the Input/output register it…

Q: Write a program in 8051 to copy the contents of code ROM addresses 0100H-0102H to internal RAM…

A: In the program microcontroller require to copy the contents from ROM address 0100H-0102H and store…

Q: Convert the following hexadecimal number to binary. (1) AE02 (2)A002

A:

Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…

A: In this question , we will write output selected  for select lines 1 1...

Q: Without using the MUL instruction, give instructions that multiply register r4 by: a)69 b)16385

A: without using MUL instruction, instructions that will multiply r4 is given below

Q: c) The input waveforms of A and B in Figure 3 are passed through the logic circuit in Figure 4. Draw…

A:

Q: If A = 1001 1001 0000 0010, show the result of the arithmetic shift right operation in hex

A: Given, binary number is A = 1001 1001 0000 0010, The arithmetic shift right operation in hex= ?

Q: Suppose r0= 0x20000080, and the memory layout is as follows: Address Data 0x20000087 0x99 0x20000086…

A: Let us examine the values of r1 and r0 for every instruction in a little-endian system. The…

Q: While CPU is executing a program, when an interrupt occurs then it O follows the next instruction in…

A: Given, While CPU is executing a program, an interrupt occurs then it

Q: Identify the type of register from the figure: Data in Do D, D2 D3 SHIFT|LOAD SRG 4 Serial data out…

A: In this we will write register type..

Q: A 10 bit ADC had a range from 0 to 12.00 V. What would be the maximum error in voltage in the…

A:

Q: Design an adder ccb that adds three 8 bib numbers using 8 bib fA blocke=-

A: Circuit which adds three 8-bits number is designed as shown below

Q: Results of arithmetic and logic instructions can be stored in one of two places. These are Program…

A:

Q: Which of these registers are not used to store the EA in the Register indirect addressing a. BX b.…

A: The correct option is SP(STACK POINTER).

Q: the initial content of a 3- bit ripple down counter is 000. After the first clock gger, the counter…

A:

Q: If the size of the memory is 1MB, what is the last address of the memory? A. Ох3FFFF OXFFFFF C.…

A: As per our company guidelines we are supposed to answer only first question kindly repost other…

Q: The main difference between a register and a counter is a register has no specific sequence of…

A: In this questions we need to tell about the main difference between register and counter.

Q: The number of clock pulses required to load the value (1011) into a 4- bit parallel load shift left…

A: A flip flop is used to store 1 bit of information to store series of data registers are used.…

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: What is the device address used by the instruction OUT A4, AL

A: OUT is a mnemonic that stands for OUTput Accumulator contents to an output port whose 8-bit address…

Q: Add 3 and 5 Carry bits 1. 4-bit number 4-bit number

A: Given :

Q: draw truth table and waveform, make sure its correct please

A: The state table can be analysed by verifying state of each flipflop after each clock.

Q: What is the weight of digit “E” in the Hexadecimal number (EA23)16 16 256 1 4096

A: the weight of the digit E is given by:

Q: multiplexer contains. multiplexer contains.... select lines 4-1 4 O 20 8 O select lines 16-1 4 O 8 5…

A: In this question we need to choose a correct option

Q: 4 to 1 What is the value of J in SoP format? MUX C' 1 Flip-Flop А В Q 2 to 4 Dec AH O A'BC + AB +…

A:

Q: What is the result of the following FAL instruction? Input L1 food А A HE О с. Ladder logic program…

A: The provided ladder logic program involves the FAL (File Arithmetic Logical) instruction, a key…

Q: If a DIP switch with 8 switches (0-7) lines up with bit0-7 of the data bus, and switches 1,2,4,5 & 7…

A: In this question,   We need to choose the correct options If switches 1,2,4,5 & 7 are set then…

Q: * bit current ADC. 0000 represents 4 4mA and 0001 represents 5mA (the resolution is 1mA). To get…

A: This question is related to Analog to digital converters

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.