vet soil sample having a volume of 75 cm is brought to the laboratory. When this soil sample is dried in the oven it weighs 14C ams. The specific gravity of the solid particles is 2.65. Find the relative density, if the maximum and minimum void ratios are 0.76 30.235, respectively. Tume of soil = V = 75 cm %3D ss of solids = m, = 140 grams a. 50% b. 60% C. 55% d. 45% e. 65% Sonraki sa

vet soil sample having a volume of 75 cm is brought to the laboratory. When this soil sample is dried in the oven it weighs 14C ams. The specific gravity of the solid particles is 2.65. Find the relative density, if the maximum and minimum void ratios are 0.76 30.235, respectively. Tume of soil = V = 75 cm %3D ss of solids = m, = 140 grams a. 50% b. 60% C. 55% d. 45% e. 65% Sonraki sa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The porosity of soil sample is 20%, the void ratio is 1. 0.20 2. 0.80 3. 1.00 4. 0.25
The properties of seven different clayey soils are shown below. Investigate the relationship between the strength and plasticity characteristics by performing the following tasks: Soil Beauharnois Detroit I Horten Gosport Mexico City Shellhaven St. Thuribe Mineral % Clay fraction (<2 μm) Kaolinite Illite 79 36 40 55 90 41 36 Montmorillonite Halloysite (hydrated) Halloysite (dehydrated) Attapulgite Allophane Activity, A 0.52 0.36 0.42 0.89 4.5 1.33 0.33 Liquid limit, LL 35-100 60-120 100-900 Undisturbed shear strength (kN/m²) 50-70 40-55 150-250 200-250 18 17 41 29 46 36 38 a. Estimate the plasticity index for each soil using Skempton's definition of activity. b. Estimate the probable mineral composition of the clay soils based on plasticity index and activity using the table below. Plastic limit, PL 20-40 35-60 50-100 Sensitivity, S, 14 40-60 30-45 100-125 120-150 2.5 17 2.2 5.3 7.6 150 Activity, A 0.3-0.5 0.5-1.2 1.5-7.0 0.1-0.2 0.4-0.6 0.4-1.3 0.4-1.3 c. Sensitivity refers to the…
Geotechnical Engineering Please help me answer this question, and please show your solutions write it properly. Problem 3 A soil sample with a grain specific gravity of 2.67 was filled in a 1000mL container in the loosest possible state and the dry unit weight of the sample was found to be 14.75 N. It was then filled at the densest obtainable state and the weight was found to be 17.70 N. The void ratio of the soil in the natural state was 0.63. Determine the relative density in the natural state.
Laboratory test results for a sample of clay soil for the purpose of evaluating the potential for volume change (swelling, expansion) are shown Liquid limit = 60% %3D Plastic limit = 24% %3D Particles smaller than 0.002 mm = 44% %3D Compute the plasticity index O 44 68 O 24 O -44
In order to calculate void ratio of a soil sample, which laboratory test(s) need(s) to be conducted? a. Liquid limit test b. Drying in oven c. Pumping well test d. Pycnometer test e. Ground Penetrating Radar tests f. Hydrometer analysis
Can u solve ?(readable) A soil specimen is 38 mm in diameter and 76 mm long, and in its natural conditionweighs 168.0 g. When dried completely in an oven, the specimen weighs 130.5 g. The value ofGs is 2.73. What is the degree of saturation of the specimen?
As a result of sieve analysis and hydrometer analysis on a soil sample, gravel 40% and sand 18%. Liquid limit value of the soil 58% and plasticity index was determined as 32%. D60, D30 and D10 values according to grain distribution curve 2.4mm, 0.9mm and 0.2mm respectively. According to the findings obtained, the soil sample Make USCS classification.
05: The Figure below represents the data that was obtained from a liquid-limit test on a soil. 50 percent of its particles is passing sieve #200. Two determinations for the plastic limit gave water contents of 20.3 % and 20.8 %. Determine 1- Liquid Limit (LL). 2- Plasticity index. 3- Liquidity index if the water content is 27.4% 4- Void ratio at the liquid limit, if G, 2.7 5- Classify the soil based on AASHTO system. 30 10 20 40 60 80 100 Penetration, d (mm) Moisture content, w ()
1. A dry sand is placed in a container having a volume of 0.0092 cubic centimeter. The dry unit weightof the sample is 0.015 gram. Water is carefully added to the container so as not to disturbed thecondition of the sand. When the container is filled, the combined weight of soil plus water is 0.0182gram.a. Determine the specific gravity of soil particle.b. Determine the dry unit weight of soil.2. If the soil sample has a water content of 11% and a unit weight of 19.67 kN/m3 , determine thepercentage of air in voids and the degree of saturation if the specific gravity of soil solid is 2.75.3. If the soil sample has a specific gravity of 2.71 and a porosity of 0.345, determine the saturated unitweight and the bouyant unit weight.4. A soil sample having a liquidity index of 0.85, a plasticity index of 16.50 and a plastic limit of 11.45.The soil sample has a specicfic gravity of 2.68 and a void ratio of 0.77.a. Compute the degree of saturation.b. Compute the air void ratio.
Discuss your results and compare your results with any published data. For the bulk density test, obtain the value of dry density. How does the values of (i) void ratio (ii) porosity influenced your results? How will these values differ if the soil is fully saturated, partially saturated or submerged? Support your assertions using relevant phase relationship equations. Whatwill happen to the values of particle density (specific gravity) obtained if the soil sample contain large quantities of peat or organic material? How will the results be used in specific practical conditions in the construction industry? Explain any source(s) of error in your experiment and state how it affected your result.