vertical, shear and moment reaction at supports A and F, internal hinges C and D, and points B and E of the beam shown below. Show FBD and Correct solutions!

Q: Draw the influence lines for the forces in the members identified by an "x" of the tru shown in the…

A: An Influence line Diagram shows the influence of effect due to load on the reactions, shear force or…

Q: Q/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20KN 4 2m 32m D 2m E…

A:

Q: Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming…

A:

Q: Construct the influence lines of each truss member. H 4 m В E 6@3 m = 18 m

A: An influence line for an obtained member, like reaction, axial force, shear force, or bending…

Q: Determine the resultant moment of forces about the point O? Neglect the beam thickness *KN 15m #2kN…

A:

Q: Determine the resultant force at pins A, C, and E. Also, determine the forces on pin D. y 80 kN/m 40…

A: in the given beam the transverse loading on the beam both shear force and bending moment my…

Q: Two 160 mm * t cover plates are welded to two cahnnels 200 mm high to form the cross section of the…

A: Introduction : Reactions : One of the most basic structures is the simply supported beam. Only two…

Q: Draw the influence line for member CG and interpret the diagram.

A: Solution: Considering the truss: When the load is in between A and B the Section1-1…

Q: 2. For the truss shown in the figure below, assume that the loads are being transmitted to the…

A:

Q: I. Determine the support reactions at A and B. Sign Convention 250KN 300KN B cw CCW 45° 2m 2.5m

A:

Q: Find the forces at Pins A, B, and D below.

A: Draw the free body diagram of member DC. Taking moment at D,

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  Influence line diagram for member DI Consider a vertical section passing through DI as shown…

Q: 5.0 The truss figure shown is pinned to the wall at point F, and supported by a roller at point C.…

A: Load act at point A= 80 kNLoad act at point B= 60 kN

Q: Cable AC exerts on beam AB a force P directed along line AC. Knowing that P must have a 350-lb…

A: Given; Vertical component of force P,Py=350lb

Q: Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section…

A: Equilibrium equations: Equilibrium equations are used to solve the unknown forces in any type of…

Q: Determine the maximum shear

A:

Q: H.W. Determine the horizontal and vertical comporents of force at pins A and D. 03n 12 KN

A: To find reactions at A and D

Q: 10 kip E | D 000 4 ft 7 kip F 000 000 4 ft A В 000 Which of the following is closest to the…

A:

Q: Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200…

A: Area of each member, A = 400mm2Young's modulus, E = 200GPaThe truss is loaded with a downwards point…

Q: Compute the reaction forces at the supports.

A: Consider the figure,

Q: or the shear at S ? Pleas

A:

Q: 2. Determine the force in each member of the space truss shown in the figure. The truss is supported…

A: Given:- The truss is supported by a ball-and-socket joint at A A slotted roller joint at B and a…

Q: Draw the influence line for member BC and interpret the diagram. H 15 ft A B. 4 @ 20 ft = 80 ft-

A:

Q: Determine is reaction at roller support B?

A:

Q: Calculate the force in member CD.

A: Find, Force in member CD

Drawing Framing Plans

A framing plan is a plan that is a blueprint to display the locations, materials (like timber, steel), spacings, sizes, framing members, and the number of structural components required to construct the house. Drawing the joists and double framing in such a position so that they can be occupied in the completed building. There is no requirement for joist dimensions at each position. Perpendicular to the joist, the drawing of bridges is made and noted as “3-2” x 3 bridgings. Wall framing plans depict the position and methodology of framing openings and heights of the ceiling so that studs and posts can be cut out. As it is a vertical plane view, technically a wall framing plan is​ not a plan.