Vertex Parabolic Force Distribution AE 300 N/m

Q: 10 - Find the center of gravity M (x,y,z) of the three-dimensional homogeneous ABCD wire in the…

A: Given data :- a = 36 cm  b = 24 cm  Find:-  Coordinates of CD part ?

Q: :Q81 The moment M for the force the figure shown below is 250 N 15 200 mm 30 mm 46.5 N.MO

A:

Q: The body on the 30° incline, shown in the figure below, is acted upon by a force P inclined at 20°…

A:

Q: w 15 kN/m 2m im 26 KN 12 Determine the resultant of the force system shown. A final pictorial is…

A: Now calculate the support reaction at point A and B asNow the net moment at point A is zero so Now…

Q: Q1. What is the linear momentum for particle A (kg.m/s)? (A) +4i+6j+6 k (B) - 4 i+6j+6 k (C)…

A: Mass of particle A is not given. please provide full question. we can solve second part for you.…

Q: 4-14. An open oil tank has a triangular gate hinged in its bottom, as shown in Figure 4.49. Find the…

A:

Q: For the portion of pipe shown, it is requested to replace the forces given by a system equivalent…

A:

Q: The figure above shows a uniform rectangular lamina OQRS, where OQ = 4a and QR a. A sector OPS of…

A: Given that, The centroid of the rectangle and sector can be given as, The sector of the quarter…

Q: Need help with all four questions please. Include units all steps. Thanks.

A:

Q: Conventional aircraft usually consist of fuselage, are not necessarily circular in form but will…

A:

Q: Cord Number of Weights Length (cm) Angle with respect to +x-axis Components of Forces Along…

A: Solution:   The filled table is shown below:

Q: What would be the resultant force Fof the triangular distributed load and its location d measured…

A: Given:

Q: (a) Use the cross product to compute the moment = about point O. Moroa X F. Express your answer as a…

A:

Q: 8'-0" 900 lb 91 006 10'-0" B 400 lb 68'-0" 48'-0" 12'-0|

A:

Q: Calculate forces (moments if applicable) for all points shown and write them down in a table.

A:

Q: Compute the coordinates of the centroid (, j) of the area shown. 2013 Michael Swanbom BY NC SA a h b…

A:

Q: 1 500 Ib/ft В 6 000 lb - 4 ft – 6 ft <

A:

Q: FA- 450 N 0.4 m 0.3 m A 450 N

A: Given that, Couple force=450 N, Write the co-ordinate of the vector as follows, A≡0,0,0.3B≡0.4,0,0.3…

Q: What is the (effective) moment arm of force F with respect to point o in the following figure? 2.2 m…

A:

Q: mathal 220 N/m 890 N/m 6 m Figure P-238

A:

Q: Find and illustrate the resultant of the distributed and concentrated loads acting on the beam.

A:

Q: I want the force for A and B by using the centroid or solve it by the right way

A:

Q: the load of 6 kN/m has been changed to 11 kN/m, • the central length of 2 m has been changed to 4 m…

A: Given: w=11 kN/ml=6 m Solution:   let The resultant is acting at x distance from point A. The…

Q: 3. Choose the best answer. From the given figure, compute the sum of moment at point C, assume…

A:

Q: splacements and reaction

A:

Q: Find the magnitude and nature of the forces in all the member of the given truss

A: The figure below represent the truss, Taking triangle AFG, tanθ1=2 m6 mθ1=18.43° Taking triangle…

Q: Draw the FBDs for the following system with its distributed loads simplified to their equivalent…

A: This question is based on the concept of free body diagram

Q: Mhat would be the resultant force F of the triangular distributed load and its location d measured…

A:

Q: Dimension decreasing for the area to volume ratio leads to:

A: This concept is based on the concept of effect of dimension on ratio of area to volume.

Q: Calculate the final output using the Centroid method for the following strength values Provide step…

A: The means for the computation of the centroid arranges, xc and yc , through reconciliation, are…

Q: For the machine element shown in the figure, locate the coordinates ft gravity. 16 mm 60 mm 28 mm 24…

A: First divide the given figure in different sections and draw the diagram

Q: The barrier shown between two water tanks of unit width (1 m) into the plane of the screen is…

A: Given:h1=4 mh2=1 mWidth of barrier=1 m

Q: 4 m + 4 m 150 KN 6m. 25 kN/m 10 m B

A: Draw the free-body diagram of the beam. Apply moment equilibrium about point A.…

Q: Q.1) For the figure shown, compute the tensions in cables AC and BC if a = 60° and P 500 N. Use sine…

A: Once applied, force is described as an external cause that alters or tends to modify the…

Q: Q3. Select the correct form of equation for the angular momentum about O (kg.m (A) Ho = ro x (MBVB +…

A: 3). angular momentum about O is... Ho=rA*mAvA +rB*mBvB+rc*mCvC Here taking cross product between…

Q: Refer the figure shown. 112 kN/m 112 kN/m 9 kN/m Etiso m t.50 m+ .50 2 m Which of the following…

A: Find the maximum bending moment.

Q: 4. Given: Curb shown below Find: (1) Surface area and (2) volume 100 mm 150 mm 4 m 30° 150 mm 150 mm

A: Given data: Angle=30° Need to determine the surface area and volume of the given shape.

Q: A pair of forces that causes one face of a material to slide relative to an adjacent face are…

A: Indirect force : Indirect force is the force applied when there is no direct contact between two…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.