venturi meter of 150 × 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5 cm of mercury (vacuum).  -Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr.

Q: A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, p = 0.038 N-s/m?) from one…

A: Introduction : Minimum costs for medium transmission through the pipeline, as well as pipe costs,…

Q: B: Answer with True (T) or False (F). 1- Manometer and Piezometer used for determine large discharge…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: 8) A private water utility purchases 10,000,000 kilowatt-hours of electricity per year for pump…

A:

Q: 450 mm 150m -0. 375 mm Mercury S = 13.6

A: Given data Diameter of inlet= 450 mm  Diameter of throat = 150 mm  Specific gravity of mercury =…

Q: a. Determine the velocity of flow in the pipe in fps. b. Determine the discharge Q in ft^3/s.…

A: Apply bernoulli equation.

Q: 1. 'Water flows through a 12 inches by 6 inches venturi meter at the rate of 1.49 ft/s and the…

A:

Q: A liquid whose specific gravity is 2.0, is flowing in a 150mm diameter pipe. The total head at a…

A:

Q: Answer with True (T) or False (F). 1- Manometer and Piezometer used for determine large discharge at…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: Please answer, hydraulics. Thanks!

A:

Q: 14.5 A differential gauge was attached to a inches. Assume no headloss. Point B is located at the 6…

A: From the given question it is required to calculate the flow rate in ft3/s.

Q: litres/s flows. All pipe sections have a diameter of 100 mm and are made of cast iron. Numbe (K)…

A:

Q: P+ 5pV² + pgz = C,

A:

Q: discharge pipe in which the velocity is 2.40m/sec. At point A in the suction p pressure is - 40kPa.…

A: Given:- diameter =200mm  discharge pipe dimater =150mm  To find:- Power

Q: PROBLEM 7 The discharge of water In the system shown below Is 0.1 m/s, x-1.0 m. y- 2.0 m, 2- 7.0m,…

A: Given  Discharge 0.1 m^3/sec No loss  Diameter of pipe 30 cm Diameter of nozzle 10 cm

Q: A Venturi Meter has water is flowing through the Venturi Meter, the pressure in the pipe and the…

A: Given, D = 0.2 m d = 0.06 m  ∆P/γ = 0.15 m

Q: Water stands in the open-ends U-tube as shown in figure below. If the entire system is rotated about…

A: Weight of liquid of height H=π4×d2×H×ρ×g     eq 1

Q: oil (0.88) oil (0.88) Hg (SG=13.6) 320mm-

A:

Q: For the system shown in the figure below, find the discharge in each pipe v-1.003-10 m³/s; 7-9810…

A: We know that friction factor is given by ; 1F = 2 log10 Re + 1.74 - For Pipe 1 : 1F1 = 2 log10 Re +…

Q: 2. The pipe shown in the figure has oil flowing with spgr of 0.82. If the total head loss from point…

A:

Q: Water flows through a horizontal venturimeter whose inlet diameter is 31cm and the throat diameter…

A:

Q: 150mm dia. 300mm dia. 800 mm Water Mercury (SG = 13.6) A vertical venturi meter 150mm diameter is…

A: Discharge can be calculated by ; Q=A1A2A12 - A222gh A1 = π4(D1)2 =  π4(0.3)2  = 0.071m2 A1 = π4(D2)2…

Q: 3: Answer either A- A submerged pipe outlet has the following data: F.S.L of distributary 100.00 m,…

A: As there are two different questions and nothing is mentioned which one to solve, So as per…

Q: Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow…

A:

Q: 300 mmø 150 mmø Hgi13.6)

A:

Q: A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Detemine the following: a.)…

A: Given data- Length of pipe (L) = 600 m Dia of pipe (D) =600 mm = 0.6 m Headloss (hf) = 1.20 m

Q: Question 5 Figure 5 shows a header tank in a laboratory. a) Determine the discharge when filling the…

A: Given, Pipe diameter AC = 22 mm Pipe diameter BC = 100 mm Pressure head at B = 35 m

Q: B: Answer with True (T) or False (F). 1- Manometer and Piezometer used for determine large discharge…

A: As per our company guidelines we are supposed to answer only first 3️⃣ sub-parts. Kindly repost…

Q: URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by…

A:

Q: A pipe system is comprised of a flush entrance, one gate valve, one 90° elbow, one 45° bend, and a…

A:

Q: M MEQ2 jpg 200mmø 690mm 300 mm 400 mmø Tit H20 LHg (13.6) A 200mm diameter venturi meter is…

A:

Q: An oil of specific gravity 0.82 is flowing through a horizontal venturimeter fitted to a 278 mm…

A:

Q: Cooling water having a density and viscosity of 998 kg/m3 and 0.95 cP is flowing thru a 25-mm med.…

A:

Q: Calculate the coefficient of discharge for the venturi meter if the flow rate is 102 m^3/hr. O 0.197…

A:

Q: A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 100…

A:

Q: Water flows from the rectangular outlet as shown in the figure. Estimate the flow rate per unit…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?