Va(V) Cal- culated Ta(A) Cal- culated Va(V) Measured Ta(A) Mea- sured p! 1 PA D1 Vin Table GND us • R = 12K • D, - 4.7V Zener Diode for circut 1 Section 1 • Construct the circuit depicted in Figure 1 on the board. Be aware that the diode in the circuit is a zener diode. Vary Vin according to the values in the first row of Table 1 and record the voltage across the diode and the current passing through the diode on Table 1 on measured row. • Using the data in the 2nd and the 3rd rows of table 1, plot the charac- teristic curve of the zener diode, Characteristic Curve using Experimental Data It is enough if you set up the circuit in a simulator program like easyeda.

Va(V) Cal- culated Ta(A) Cal- culated Va(V) Measured Ta(A) Mea- sured p! 1 PA D1 Vin Table GND us • R = 12K • D, - 4.7V Zener Diode for circut 1 Section 1 • Construct the circuit depicted in Figure 1 on the board. Be aware that the diode in the circuit is a zener diode. Vary Vin according to the values in the first row of Table 1 and record the voltage across the diode and the current passing through the diode on Table 1 on measured row. • Using the data in the 2nd and the 3rd rows of table 1, plot the charac- teristic curve of the zener diode, Characteristic Curve using Experimental Data It is enough if you set up the circuit in a simulator program like easyeda.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If Vz-8 V and Pzmax=150mW. Determine the minimum value of RL to ensure the Zener diode is in the ON state 14 118 Ohm 210 Ohm 235 Ohm 105 Ohm 470 0 33°C Activate Windo Go to Settings to ac c's
Assuming a Buck converter is operating in continuous conduction mode with a duty ratio & and an output current lo, which of the following expressions correctly describes the average diode current? 07₁=1 (1-8) O 01₁=1₁ OÏDE =I I ° ;,-' == D O 06-1/ = D 1-8
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. 9kO IN1199C R2 01 18KO IN11990 D3 IN1199C R3 V2 12 V R4 5kQ
If the diode is ON, what is resistor current and Vo? Assume an ideal diode.
when the diode ideal. the value of I and V D1 +1 Vo– +2 V o– D2 2 k2 -5 V |
For each circuit, use the diode approximation with the forward drop equal to 0.7 V and determine Vout. +3 V 10 k - Vout -3 V ++3 V 10 k - Vout -3 V ++3 V 10 k 5 k -3 V Vout
5V 3000 1000 . 2m 1 Si 4000 500 12V The circuit shown in Figure 1 contains a Si diode with a diode resistance on 1000. Use the piecewise linear model to solve the circuit. • How many nodes are in the circuit? • Determine the Thevenin voltage across the diode. Replace the diode with the appropriate model and then solve the circuit to determine the power dissipated by each resistor and the diode.
Quiq
What could happen to the diode if the I-V characteristic curve is linear?
5. Determine I, Vsi, V1, V3 and Vout for the diode circuit in Figure 4 below. Vi Si 8V Vin=18V R1=1002 R-472 R2=2.k2, V3 V2 Figure 4
Is the diode forward biased or reversed biased on the given circuit below? (Answer forward biased or reversed biased only) un A K
What are the different types of 4 layered diode