Example 6:Water (T = 20°C) flows at a rate of 0.05 m³/s in a 20-cm asphaltedcast iron pipe. What is the head loss per kilometer of pipe?Assume the flow is fully developed. Kinematic viscosity: v= 1 x 10-6 m²/sWater, 20°CQ=0.05 m³/sL = 1000 mD = 0.2 mAsphalted, cast iron

- Temperature of water at inlet (T1) = 200C- Flow rate = 0.05m3/S- Iron pipe diameter (D) = 0.2m-…

Vater (T = 20°C) flows at a rate of 0.05 m³/s in a 20-cm asphalted ast iron pipe. What is the head loss per kilometer of pipe? ssume the flow is fully developed. Kinematic viscosity: v = 1 × 10-6 m²/s Water, 20°C L = 1000 m

Vater (T = 20°C) flows at a rate of 0.05 m³/s in a 20-cm asphalted ast iron pipe. What is the head loss per kilometer of pipe? ssume the flow is fully developed. Kinematic viscosity: v = 1 × 10-6 m²/s Water, 20°C L = 1000 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.12P

See similar textbooks

Similar questions

In a dyehouse, the water flow rate passing through a pipe with radius r is Q = 0.05 m3 / s and its density is ρ = 1000 kg / m3. The pipe friction coefficient is Cf = 0.0075 and the local loss coefficient is K = 10. Pressure drop in the pipe; LaTeX: \ Delta P = \ rho \ left (2Cf \ ast \ frac {L} (r} + K \ right) \ frac (V ^ 2} (2) ΔP = ρ (2Cf * Lr + K) V22 where the water velocity in the pipe can be calculated with V = Q / (r2). What should be the radius of the pipe so that the pressure drop that will occur in a pipe of L = 100 m length does not exceed =P = 200 000 N / m2? State the tolerance value provided by the result you found.
sg
03. Find the pressure difference between A and B Oil RD = 0.8 Water 0.4m 0.2m 0.3m Water 0.4m 0.4m (a) 1692 Pa (b) 1913 Pa (c) 2141 Pa (d) 2551 Pa
Mc = 3050g Ms = 800g Mss = 820g Mws = 3450g Calculate the values of: Mw = Ms 1. Bulk (O.D.) Specific Gravity = (Mc+Mss-Mws) Mss 2. Bulk (SSD) Specific Gravity =- (Mc+Mss-Mws) Ms 3. Apparent Specific Gravity =. (Mc+Ms-Mws) Mss-Ms 4. Percent Absorption = x 100% Ms
Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the head loss in terms of inches over a 200-feet long section of the pipe. A) 327.60 В 27.30 C 376.05 D None of the above
Compute the head loss (in meters) in 2000 m of horizontal, steel pipe with nominal pipe size of 300 mm and SCH 30. The pipe is carrying water with an average velocity of 1.88 m/s. Take water at 20°C to have a viscosity of 1.00E-3 Pa-s and density of 1000 kg/(m^3). Take the roughness of steel pipe to be 0.048 mm. Round your answer to 2 decimal places.
10.ln turbulent flow the losses are proportional to the velocity. hl&v O true O False
3. Circular clarifiers are used to remove solid materials from water. They allow continuous treatment of water and can handle fairly large flows. Solids settle to the bottom of the clarifier and are carried away by a small stream of water (the waste stream). Most of the water exits the tank as treated effluent. Assume a clarifier receives a flow of 0.10 m3/s with a solid concentration of 800 mg/L. If the waste stream consists of 3% of the incoming flow and carries 90% of the incoming solids, a) what is the solids concentration in the waste stream, and b) what is the solids concentration in the treated effluent?
Seepage force per unit volume can be expressed as (A) iy„L (B) iL (C) Y,h (D) iy.
Water is flowing through three soil layers as shown in Fig. Q2. The cross-section is a square with sides of 100 mm. The hydraulic conductivity (also known as coefficient of permeability) of each soil layer is given in Table Q2. a. What is the equivalent hydraulic conductivity of the three layers? b. Determine the flow rate exiting the system. c. Determine the elevation head diagram, the total head diagram, and the pressure head diagram from point A to point B. Ah = 30 cm h, = 50 cm h2 = 20 cm B D = 10 cm 3.33 cm 3.33 сm 3.33 cm O Datum 45 cm O Datum Fig. Q2: Three-layer permeameter
Given:Flow rate of water = 500 L/minSuspended solids concentration in influent water = 100 mg/LRequired effluent suspended solids concentration = 10 mg/LFiltration rate = 10 m^3/m^2/hrFiltration tank dimensions: Length = 5 m, Width = 3 m, Depth = 4 mCalculate:o Calculate the total suspended solids (TSS) load in the influent water:o Calculate the filtration tank surface area:o Calculate the required filtration tank capacity:o Calculate the required detention time in the filtration tank: Q2) DisinfectionGiven:Flow rate of water = 2000 m^3/hChlorine residual required in effluent = 0.5 mg/LInitial chlorine concentration in influent water = 2 mg/LChlorine decay rate in disinfection tank = 0.05 per hourDisinfection tank volume = 300 m^3Calculate:o Calculate the chlorine demand in the influent water:o Calculate the chlorine dosage required:o Calculate the chlorine dosage rate:o Calculate the actual chlorine dosage rate considering chlorine decay:
Problem 1 Oil, with density of 900 kg/m³ and kinematic viscosity of 0.00001 m²/s, flows at 0.2 m³/s through 500 m of 200-mm-diameter cast-iron pipe (roughness: 0.26 mm). Determine the head loss (in m) and pressure drop (in kPa) if the pipe slopes down at 10° in the flow direction. Assume α = 1.0 throughout.