to tuvalloll Theorypoy7. Given a QPSK signal vopSK (t) = 2b,(t)sin(2n x 105t)+ 2b.(t)cos(2n × 105t) where b.(t), be(t) take a valuece(1) ('(2) ,(3) (·(4)(5) (of -1 or 1 every 6 seconds. For vopSK(t), determine) signal power Ps;symbol period Ts and bit period T,;nominal bandwidth BoPK;) energy per symbol Es and energy per bit E,;minimum distance between symbols dopSK.

“Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

valiVl 1heory. 7. Given a QPSK signal vopSK (t) = 2b,(t)sin(2n × 105t) + 2b.(t)cos(2 × 105t) where b.(t), be(t) take a value of -1 or 1 every 6 seconds. For vopSK(t), determine (1) ( ) signal power Ps; (2), symbol period Ts and bit period Tpi (3) nominal bandwidth BOPK; (4) (5) ( ) energy per symbol Es and energy per bit E,; minimum distance between symbols dopSK-

valiVl 1heory. 7. Given a QPSK signal vopSK (t) = 2b,(t)sin(2n × 105t) + 2b.(t)cos(2 × 105t) where b.(t), be(t) take a value of -1 or 1 every 6 seconds. For vopSK(t), determine (1) ( ) signal power Ps; (2), symbol period Ts and bit period Tpi (3) nominal bandwidth BOPK; (4) (5) ( ) energy per symbol Es and energy per bit E,; minimum distance between symbols dopSK-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 6 SPM(t) and Sy(t) as defined below, are the phase modulated and the frequency modulated waveforms, respectively, corresponding to the message signal m(t) shown in the figure. SPMt) = cos(1000nt + K, m(t)) and SEMI) = cos 1000rt + K m(t) dt %3D -0- where K, is the phase deviation constant in radians/volt and K, is the frequency deviation constant in radians/second/volt. If the highest instantaneous frequencies of SPM(t) and Kp is SEM1) are same, then the value of the ratio seconds. AV in m(t) 10 1 3 6 7 t (sec)
Write the equations for ØAM(1), ØFM(t) and ØPM(1), if the modulating signal is; f(1) = 2cos300ti + 4cos600ni
Classification of Signals By inspecting plots (a) and (b) in the following Figure. classify the CT waveforms as even versus odd, and periodic versus aperiodic. If the waveform is neither even nor odd, then determine the even and odd components of the signal. For periodic signals, determine the fundamental period. (a) -2 -1 x₁(1) 01 2 3 4 (b) x₂(1) 2.5 www. -2.5 4
A carrier wave of 30 V amplitude and 6 KHz frequency is modulated by an information signal m(t)=4sin(200t)-6cos(400t). Write the modulated signal spectrum.
A plot of the exponential spectrum of the signal x(t) = 4 sin(200πt) +12 sin(1000 πt) will have a peak amplitude of _______ at -500Hz as well as a bandwidth of ______Hz.. Single choice.
A sequence of alternating 1s and 0s is transmitted as a square wave. What is the fundamentalfrequency and how many harmonics can be used if the available BW is 100 MHz and a data rate of 56Mbps is desired? Express the signal as a mathematical function of time (s(t)) and sketch the resultingsignal in both the time and frequency domains. Is this a “good enough” representation of the squarewave? Why or why not?
1. A sequence of alternating 1s and Os is transmitted as a square wave. What is the fundamental frequency and how many harmonics can be used if the available BW is 100 MHz and a data rate of 56 Mbps is desired? Express the signal as a mathematical function of time (s(1)) and sketch the resulting signal in both the time and frequency domains. Is this a "good enough" representation of the square wave? Why or why not?
What is the resulting signal of the following Hartley SSB modulator? + sin 2πfet m(t)- -π/2 a. The inverted LSSB signal. O b. The USSB signal. O c. The LSSB signal. O d. The inverted USSB signal. + cos 2πfct
In an Amplitude modulator, the carrier is v. = -12 sin[2n(100 x 103)t]. If the modulating signal is Vm = 3 cos[2n(800)t)]: a) Determine the equation of the modulated signal b) Sketch the frequency spectrum of the modulated signal (label amplitudes and frequencies) c) Calculate the effective voltage of the modulated signal
Is the small signal model of the circuit correct?If yes, proceed in answering the questions; if not, correct the model first, then answer the questions. Note: ignore the parasitic capacitances
0.5 -6 -2 4. 6. time in seconds What, signal is plotted above? O Type here to search %23 76°F A OE O 0 deete home backspack 80 QWE R
1. What is the Nyquist frequency for this signal? cos(3000t) cos (3000.t) + cos(5000zt)