Answered: VAB 49:113 49.113 4m VBD 15-444 VED VDE…

VAB 49:113 49.113 4m VBD 15-444 VED VDE 45.13 ↑ VEG 45.13 3m 30 ким ↓ ↓ bm d 112.433 งา VGE 22.944 5m 24-01 70.5745 JOB TUDE 4M UFD 0.5745 VDC 2m VCD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam carries various loadings as shown in the figure. An internal hinge is located at C. Calculate the maximum shearing force and maximum bending moment. What is the resultant reaction force and bending moment at support D? Draw the complete shear and moment diagrams on your solution paper
can you please give a short and easy example problem and solution on this.
Please answer attached image.thank you
For the beam shown, the magnitude of the distributed load is wo = 11.8 kN/m and the beam length is L = 8.0 m. (a) derive equations for the shear force Vand the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A B L Answer: Vmax = kN Mmax = kN-m
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1. What is the shear at E? 2. What is the shear and moment at point C? 3. What is the shear and moment at point A? please provide a solution, thank u so much.Given: Shear and moment at left of C Vc= -4.5 kn Mc= -4.5 kn-m Shear and moment at right of C Vc= 37.5 knMc= -94.5 kn-m
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. The unit vector ÅBc 3. The position vector Tɛ/a 4. The position vector īB/a
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P A C D E Answer: (a) Vmax= (b) Mmax= a B b lb b lb-ft a
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 5.0 m, b = 1.7 m, wA = 16 kN/m, and wB = 46 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.