Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P W A B E Answer: (a) Vmax= (b) Mmax = a b C lb b lb-ft D a

Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 3.3 ft, b = 3.2 ft, P = 20 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P W A B E Answer: (a) Vmax= (b) Mmax = a b C lb b lb-ft D a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure Q1 shows a statically determinate plane truss subjected to a verticalconcentrated load at C and E. The truss is made using steel with Modulus of Elasticity is210 GPa, and the cross section area for all members are 30 mm2. Assuming P is the 10 and a is half of P, determine the vertical displacement at F. Thesolution can be based on Method of Conservation Energy or Method of Virtual Work.
Solve last 2 parts
The beam shown in the Figure q2 below is a continuous beam of 2 spans. Determine the reactions at the supports using a method of stiffness matrix. Assume 1 and 3 are fixed and 2 is a roller. El is constant. 5 6 1 10 kN/m -5 m 2 FIGURE Q2 2 5 kN/m 2 4 m 3 3 4
4. For the beam loaded as shown in the figure, determine displacement at B using moment-area theorems. EI is constant
P= 77kN
Apply the asymmetric bending theory to the cantilever beam shown below to determine:I. Main moments and inertias.II. The angle of the neutral axis respect the horizontal.III. If ???? = (table) ???, work out the maximum F force that can be applied.3L = (7.5) mb = (57) cmh = (47) cmθ = (56) ° mpa 30
Consider the frame shown below: (a) Without conducting any analyses, which of the two columns, AB and CD, is expected to experience a larger shear force? Explain the reasons, (b) Using the slope-deflection equations, determine the end moments of all members, (c) Compute the horizontal reactions at points A and D and compare the result with the expectation from part (a). EI is constant and all members are axially rigid. 10 kips B 15 ft A 10 ft с 10 ft D
14. Determine the pressure increase (in Pascal) required to reduce the volume of water by 1.5%, if the bulk modulus of elasticity is 2.2 x 10^9 Pa. (3 decimal places in scientific notation of 10^9)
Please go through the image , and solve it completely with neat free body diagrams thanks.....
For the beam and loading shown below, determine the reactions at supports A and B. Assume that EI = 8.6× 106 kip·in.2 is constant for the beam. Use w = 11 kips/ft and L = 12 ft. Remove support C and use the appropriate equations from Appendix C to calculate the deflection at point C caused by the distributed load. Use the sign convention from the textbook (deflection is positive upward).
A beam is loaded and supported as shown. Use the double-integration method to determine the reactions at supports A and B. Assume wo = 10 kN/m and L = 9 m. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. Cut a cross-section through the beam and draw a free body diagram to the left of the cut. Determine the internal bending moment in terms of Ay. Check your equation by solving for M(x) at x = 4.5 m. Answer:Mx=4.5m = kN·m + m Ay
3. A T-shaped structure is acted in by a distributed load that varies from 100 N/m to 0 N/m and by a force P. Attached at A and C are two cables. Each of the cables is attached to a ring at E. A 600 N weight is suspended from the ring. The structure can rotate about B but is held in the position shown by the force P. a. From the geometry of the problem, determine the distance d, b. If the total moment about B is equal to zero, what is the magnitude of force P, and c. Determine the tensions in cables EA and EC. B 100 N/m 0.825 A 1.50- P 78° -0.625 260 E 600 N