Answered: V1 20V R1 100kOhm C1 50Uf In the given… | bartleby

Related questions

Question

V1
20V
R1
100kOhm
C1
50μF
In the given circuit, calculate the time after connection when the resistor voltage is 18.
Final answer should be in four (4) decimal places.
• For the final answer, express the unit in symbols. For example:
。 5.00 Kelvin should be expressed as 5.00 K
• DO NOT answer in exponential form.
Express your answer in seconds (s).

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Constants During an action potential, Nat ions move into the cell at a rate of about 3 x 10-7mol/m? •S. Part A How much power must be produced by the "active Nat pumping" system to produce this flow against a +30-mV potential difference? Assume that the axon is 10 cm long and 30 µm in diameter. Express your answer using two significant figures. ? P = W
P Performance Matters Welcome, Bertiana! ► || A Tools - Question 2 of 51 Submit Test 04.CFE.2003380.2003390.2003836.2003840.Phy... A cell phone will typically have a power output of 1.4 watts when playing a song that lasts for 300 seconds. If the electrical resistance of the cellphone is 400 Q, what is the total charge needed to play the song?
Determine the magnitudes and directions of the currents in each resistor shown in the figure. The batteries have emfs of E1 = 8.2 V and E2= 11.8 V and the resistors have values of R1 = 30 Ω , R2 = 36 Ω , and R3 = 34 Ω. Part A) Ignore internal resistance of the batteries. Express your answers using two significant figures. Enter your answers numerically separated by commas. Part B) Which way is I1 directed? Part C) Which way is I2 directed? Part D) Which was is I3 directed? Part E) Assume each battery has internal resistance 1.3 Ω .Express your answers using two significant figures. Enter your answers numerically separated by commas. Part F) Directions of all I? Sorry for the length! thank you!
When an ammeter is used to measure the current is in the circuit shown in (Figure 1 ), it reads 6 A. Part A What is the resistance of the ammeter if v₂ = 27 V? Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) Figure 2.516 Us is 4.80 16 1 of 1 με ? Rmeter 4.5 Ω Submit Previous Answers × Incorrect; Try Again; 2 attempts remaining Part B What is the percentage of error in the current measurement? Express your answer as a percentage to three significant figures. ▸ View Available Hint(s) % error = 40 ΜΕ ΑΣΦ Η vec Submit Previous Answers × Incorrect; Try Again; 5 attempts remaining < Return to Assignment Provide Feedback ? %
1 The combined electrical resistance R of two resistors R₁ and R₂, connected in parallel, is given by the equation below, where R, R₁, and R₂ are measured in ohms. R₁ and R₂ are increasing at rates of 0.6 and 1.9 ohms per second, respectively. = 1/² + 12/2₂2 R₁ At what rate is R changing when R₁ ohm/sec R 55 ohms and R₂ = 88 ohms? (Round your answer to three decimal places.)
A 0.460-mm-diameter silver wire carries a 10.0 mA current. Part A What is the electric field in the wire? Express your answer with the appropriate units. • View Available Hint(s) HẢ ? E = Value Units Submit Part B What is the electron drift speed in the wire? Express your answer with the appropriate units. • View Available Hint(s) µA ?
6) In recent class lectures, we discussed the temperature dependence of the electrical resistivity, p(T) for the three main classes of materials that conduct an electrical current; conductors, semiconductors, and superconductors. In the graph below, draw in by hand examples of the temperature dependence of the electrical resistivity, pT), for each material type. Give at least one example of each material type. plT) + +>T(K) 100 200 300
Subject: phy
Select the correct value for each of the quantities listed below. A capacitor of capacitance C= 2.0 µF is initially charged with charge Qo = 6.0 µC. The %3D capacitor is then discharged by connecting it to a resistor of resistance R = 5.0 MN. V V. • The initial voltage of this capacitor is [Select ] At time t = 20 s: • the charge on the capacitor is Q = [Select ] µC, • the voltage across the capacitor is AV= [Select] Y V, • the current in the circuit is I = [ Select ] [ Select ] and the energy stored in the capacitor is U =