v what is the distance

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:-  Scale length = 84 mm Actual length = 63 m = 63000 mm  To Find:-  Scale

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: ?What is the final reading of Vernier caliper from the figure given below 10 30 40 50 20

A: The main scale reading =5mm Vernier scale reading=0.775mm

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: What is the reading of the following Verner caliper? 4. 5 6 7 8 10

A: Given Data⇒ Vernier Caliper reading Smallest reading on the main scale=0.1 Number of divisions on…

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: The figure below shows a Venturi meter for measuring the water flow rate through a pipe. The…

A: GivenA1=0.01m2A2=0.006m2S.G=1.4h=0.8mg=9.81m/s2ρw=1000 kg/m3

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: There were 8-track tapes made in what year.

A: In audio and video recording, a cassette, sometimes known as a tape cassette, is a flat, rectangular…

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: Can you put all the measurements, as in all measurements and make it in centimeters?

A: given : Isometric view

Q: Draw the Venn Diagram and write your answer in set roster notation. 5 pts A={1,2,3,4} B ={1,3,5,7}…

A: Venn diagrams are used to establish relation between things or a finite group of things with the…

Q: Which is the final element of a measurement system ?

A: The measurement system is defined as a system which is used to specify the physical quantity of an…

Q: what is the bottom length?

A: To calculate the bottom length

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: Make an orthographic projection.

A: The orthographic views for the given isometric object are drawn below with the actual scale 1:1

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: 0 = 0° A

A:

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of…

A: Introduction: Engineering drawings are a subset of technical drawings. The goal is to provide all of…

Q: The temperature of the potato, which was cooked in a constant temperature oven, increased by 7C in…

A: Heat transfer in the oven is mainly due to radiation. Radiation heat transfer between two objects…

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Q: What is the diameter of the groove?

A: Let us discuss given engineering drawing to find diameter of groove.