uzzle velocity of 150 m/sec. directed upward at 60o with the horizontal. Determine the a) total time of flight. b) Maximum height it reached. c) Location of the shell after 20 sec it was fired d) its resultant velocity 18 sec. after it was fired.

Q: Compart The & filled with air. When the gauges (A) 4 (D) read as indicated, what should be the value…

A: Manometers are the device used for measuring the pressure in a fluid at a point. 1Bar=105 N/m2…

Q: A U-tube differential manometer: b) a) is used upright when pressure difference is large is used…

A: A U-tube manometer is a tool used to calculate the fluid's pressure differential between two places.…

Q: The steel bat All has a rectangular cross section (E1) Figure 3m -20 mm 30 mm 20 mm tof 1 Part A it…

A: The load acting at on the column AB through the beam BC is given by (wL/2) = (w x 5 /2…

Q: 1. Three pipes of different lengths and diameters connected in series as shown discharges 169…

A:

Q: Ex: Giren Li-toom, D = 50mm, L2= foom, D₂ = 100mm (orall pipes) = 0.032, Find:. a-Discharge of each…

A:

Q: An unsymmetrical sprinkler has frictionless and equal flow through each of the two nozzles. If the…

A:

Q: The theoretical discharge "Qt" can be computed by multiplying the actual value by the coefficient of…

A: Incorrect

Q: P+ 5pV² + pgz = C,

A:

Q: Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What…

A: The values and diagram given in the question are as follows The specific gravity of glycerine=1.26…

Q: A piece of lead pipe of outer diameter 2.75 in. and inner diameter 2.25 in. , and length of 16 ft.,…

A: Given data: D=2.75 in. d=2.25 in. L=16 ft conical pot radius= 10 in altitude= 15 in

Q: Calculate the force exerted on the bolt connecting the pipe as water flows through the pipe in…

A:

Q: a.) What is the value of (theta/angle) to obtain the smallest possible value of P so that the crate…

A:

Q: Date No. The water mercury manometer of Ergure shown Indicates lifferential reading of o.30m a hen…

A: Specific gravity of oil is taken as .93 and of mercury as 13.6

Q: Which of the following pressure-tap arrangements will yield the lowest pressure drop reading for an…

A: Orifice pressure tap positions are defined by a number of standards. The upstream pressure tap…

Q: Which of the following best describes a Venturi Meter? an opening having a closed O perimeter in a…

A: Venturimeter are Flow Measurement Instruments Which uses a converging section of pipe where we apply…

Q: A shell leaves a mortar with a muzzle velocity of 500ft/sec directed upward at 60 degrees with the…

A:

Q: Analyze the free-body diagram, given the coefficients of static and kinetic friction. Determine…

A:

Q: Select all true statements. The advantage(s) of using two primers initiated at the same time…

A: statement wise explanation whether it's true or false with its reason is explained below. defining…

Q: s problem uses Figure 2 L. Select all that are true about this manometer set-up. Орen (4) Y2 Y1 (1)…

A:

Q: A 20-lb projectile is moving with a velocity of 92 ft/s when it explodes into 5 and 15-lb fragments.…

A: FBD of the given problem:

Q: a. If the mass of bullet is 5g and the mass of the gun is 10kg and the velocity of the bullet is…

A:

Q: Kerosene (s.g.-0.82) enters the cylindrical arrangement of the figure shown at section 1, at 0.56…

A:

Q: Date Determination of Discharge Using a Venturi Meter tamula: Vol. %3D も PZ 29 trial #1 trial #2 H…

A:

Q: 1.) For the water shooting out of the pipe and nozzle under the condition showed, find the height…

A: Given: A jet is given provided with the nozzle diameter of 100mm. PA=55kPa Diameter at  A, DA=200mm…

Q: A 60 MLD water treatment plant has 4 mechanical flocculators. The design criteria for each…

A: Detention time=25min Discharge=60MLD

Q: 1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow…

A: Frictional loss is due to shear stress in the walls of the pipe.

Q: .Determine the minimum cylinder mass m1 required to cause loss of contact at A A 30° 21/3 m L/3 B m1

A: We need to determine minimum mass of cylinder m1 to cause loss of contact at A

Q: A projectile is fired with a speed of 60m/s at an angle of 60 degrees from the ground surface. A…

A:

Q: 1. Determine the minimum cylinder mass m1 required to cause loss of contact at A. 43 2 L/3 m 1/3 B…

A: Given- angle= 43 AO= 2L/3 OB= L/3   To find m1 for losing contact at A

Q: Cross sectional area: 4 meter by 4 meter, three consecutive flocculation tanks. a) Determine the…

A: A.  4m/nB.1.  v2= 50m/s     v3= 30m/s2. n1= 0.3183/s    n2= 7.9577/s    n3= 3.1831/s3. P=0.0002WC.…

Q: A shell leaves a mortar with a muzzle velocity of 500ft/s directed upward at 60° with the…

A:

Q: If you needed to locate a leak in a dam the __________ method would be helpful. I am confused. but…

A: Electrical resistivity method- It is a non-intrusive geophysical method used to detect seepage in…

Q: sump, then pumped back to the roof tank after the experiment (see Fig. Q4 below). The flowrate was…

A: According to given data The flow rate was 10 litre /s The tank was 6m above the sump length of the…

Q: H.W-2 A projectile is fired with an initial velocity of "A-150 m/s off the roof of the building.…

A: If you have any questions please let me know in comments.Hope it helps.Thankyou

Q: Heavy oil discharges from a pipe through a sharp-crested, 100-mm-diameter orifice having discharge…

A:

Q: th the horizontal. 20 sec after firing. 5000

A:

Q: discharge in pipe no. 1. = _________ m3/s head loss in pipe no. 3. = _________ meter discharge…

A:

Q: ... 300 mmg 100 mmø H20, 500mm EHgC(13-6) A 100mm diameter venturi meter is installed in a 300mm…

A:

Q: (Ch4-1] What is the head loss and corresponding pressure drop (in units of bars) across a 30-…

A: As per guidelines we need to answer only first question so please repost rest questions separately.

Thermal Processes

Some of the key areas where thermal processes find their application are: