Using the double integration method, determine the value of the slope at point B and the vertical displacement at point A. Assume E=200 GPa. also draw the deformed with the calculated data.

Q: Question 2 Determine the moment of inertia of the area about the x axis as shown in Figure Q2.…

A: Given,to determine,Moment of inertia about the x-axis(a) having a thickness of dx(b) having a…

Q: 1-30. A differential element taken from a curved bar is shown in the figure. Show that dN/d0 = V,…

A: Given data,Differential element taken from curved bar givenShow that

Q: 2. Test for exactness. If exact, solve. (a) (x² + y²) – 2xyy' = 0 (b) e3º (dr + 3r d0) = 0 (c)…

A:

Q: . Determine the ratio To/T,

A:

Q: as shown in nd Poisson ra

A:

Q: 03 A F1 = 1300N, F, = 1850N, F; 3500N O1 = 70°, 02 155°, 03 = 200° The point A is acted upòn by…

A:

Q: Problem 2. Use virtual work method and determine the following unknowns on the truss system shown…

A:

Q: Example 14.2. Determine the displacement at C and the slope at A of the beam. El is constant. These…

A: Procedure for Analysis by Singularity Function Method Draw the free-body diagram of the beam and…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equ curve for…

A:

Q: y F = 25 kN P = 75 kN 6 cm. 4.8 cm 2.4 cm '4 cm 3.6 сm 10 cm

A:

Q: Given z= /1+xy and (x,y) changes from (2, 1) to (1.97, 1.04). (a) Use total differential to find the…

A: We have to calculate  z=1+xyby using differential to app. to ∆z and Exact change in z And app. of z…

Q: Problem 7: Non-circular cross section shaft related to torque problems are difficult to be solved…

A: The finite element analysis is complicated by the fact that problem in 2D ae described by partial…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: Determine the following unknowns on the beam shown below using Double Integration Method. Consider…

A: Given data:

Q: Interpolate between In (4) = 1.386294361 and In (8) = 2.079441542. Also, compute the percent…

A: Given  Ln(4) =1.386294361  Ln(8) = 2.079441542

Q: Solve and Include the given with the required quantities and draw the diagram of the given problem.…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Input values in two (2)…

A: A piece of member is given and it has been asked to determine centroid of the same. Please refer…

Q: rite the difference between felixiblity method and stiffness method

A: STIFFNESS METHOD  FLEXIBILITY METHOD This method is applicable to statically determinate as…

Q: The rigid bar AB, attached to aluminum and steel rods, is horizontal before the load P is applied.…

A:

Q: legibly. Box your final answer at the first page of your solution file. Determine the deflection at…

A: Using double integration method:-

Q: Find the root of the function f(x) = e 2x – x – 6. Correct to four decimal places. Use initial guess…

A:

Q: Find the value of displacement if force applied is 12 N and work done is 63 i

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: 1. Compute the vertical and horizontal components of displacement of joint E produced by the loads.…

A: Given  Area of AB,BD ,CD = 5 IN 2 All other = 3 in2   E= 30000 kips /in 2

Q: Example 2: giveny(x, t) = 4sin3x cos2t , find 2 and 2 ду %3D ax at

A:

Q: The next iterative value of the root of (x^2)-4 using the Newton-Raphson method, if the initial…

A: To determine the next iterative root of a given function for a given initial guess using…

Q: The frame is subjected to distributed load of 500 kN/m as shown in the figure. Analyse the response…

A: E = 2.05e8  # Young's modulus in kN/m2I = 5.54e-4  # Moment of inertia in m4A = 0.012  #…

Q: The differential equation for a vibrating system damped by a force proportional to thevelocity and…

A:

Q: Find the beam deflection y(x) that satisfies EI= W(x) for 0 <x< 2c . Wo 30 UIN

A:

Q: Problem: For the beam and loading shown, determine (a) the equation of the elastic curve, and (b)…

A:

Q: 1.5 m B -1 m z 2 kN A

A:

Q: Determine the displacement at C measured upward. Express your answer using three significant…

A: Displacement at C and Slope At D Using Conjugate Beam Method ####

Q: [1] For the quadrilateral element shown in Figure below, evaluate the stiffness matrix coefficient…

A:

Q: Hiwe A bar with Constant oss-Sectian avea(Al anod unit weight () is subjected to axial force (P) in…

A:

Q: Find the particular solution for: y' sin(2y) – cosx = 0, x = -when y = 0 %3D

A:

Q: Find a formula for cos (30) in terms of cos (0) and sin (0) using de Moivre's Theorem.

A: To find a formula for cos(3θ) in terms of cos(θ) and sin(θ) using De Moivre's Theorem, we can apply…

Q: A 7.5m cantilever beam shown carries a 115KN/m uniform load. Point A is free end while point B is…

A: Given data in question  Length 7.5 m UDL 115 kN/m A is free end To find out  Value of EIY at free…

Q: • D=8¹ • 1 = 25.914 WOTE Solution not required

A:

Q: Remove the distributed load w = 10.0 kN/m and determine the deflection of the beam at B due to the…

A:

Q: Consider a two-dimensional problem. The stress transformation formulae are then. in full, cos 8-sin…

A: The stress transformation formulas for a two-dimensional problem are:σ'x = σx cos2(θ) + 2τxy sin(θ)…

Q: From the following beam, determine the deflection in b and c, according to the virtual work method,…

A:

Q: 200 mm O mm 25 mm V 50 mm 30 mm 100 mm

A: given v=23KNI=198×106mm4y=182.54mm from bottomwe know thatζ=VAyIbwhere V= forced appliedζ= shear…