Using the constant-voltage model (all diode's turn- on voltage, V_D = 0.7V), plot the input vs. output characteristics (VTC, voltage transfer characteristic). On your plot, x-axis is V1 and y-axis is VO . In your plot, you have to mark the slope and the values on x-y axis in detail. D3 D4 o Vo 1ka 2kn

Using the constant-voltage model (all diode's turn- on voltage, V_D = 0.7V), plot the input vs. output characteristics (VTC, voltage transfer characteristic). On your plot, x-axis is V1 and y-axis is VO . In your plot, you have to mark the slope and the values on x-y axis in detail. D3 D4 o Vo 1ka 2kn

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

for the given circuit, input voltage is AC(10,-10)v, R=2KQ , diode is ideal. what is the Vout in the positive and negative cycle ? just write numbers example: 5v,6v ..
find the diode voltage and diode current with solution.
For the following circuit: Find the current that goes through each diode. What's the value of Vo? Invert polarity of the 5V source and obtain the following: Find the current that goes through each diode. What's the value of Vo? V1 -5V H D1 1N4001 R2 >1kQ 11 D2 1N4001 R1 2kQ ww R3 1kQ Vo Use simplified model
ANSWER THE QUESTION
5 For the following circuit: a) Draw a table to mention the names, the states (ON/OFF) and turn on voltages for all the diodes of the circuit. (V = 3.5V for D3) and draw the equivalent circuit. b) Find the voltage across R1, R2, R3 c) Find the current through D1 , Dz , D3 and D4 D1 Si R2 D2 5002 Si R1 7502 R3 D3 D4 V1 1kn Blue GaAs 10v
A silicon diode has an incremental resistance “R”. It is then connected in series with a resistor 25 ohms across a 25V source. If the voltage drop across the 25 ohm resistor is 10 V, what is the value of “R” ?
For the diode circuit to the right 8002 a V 1002 b 40mA 0.001V' a) To the left of points a and b, find the load-line relation by expressing the current, I with voltage, V. HINT: Write KCL equation for the circuit diagram and write I in terms of V from that KCL equation. This will be your load-line equation. b) Assume the diode has the following characteristic, using the load-line relation you found in (a), determine the operating voltage, V and current, I for the circuit. ip (mA) 20 15 10 5 Vp (V) 3.0 0.5 '1.0 1.5 2.0 2.5
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode
In the circuit shown below. Let Vm-35 V and i-20 mA and VpQ -0.7 V: iD 3 kQ 0.8 kO Vmcos(@t)V For t Os, the current in the diode equals: Oa. 0 mA Ob. 4 mA Oc. 2 mA Od. 6 mA If t = T/4, then the current in the diode equals: Oa. 6.29 mA Ob. 5.03 mA Oc. 4,03 mA Od. 7.86 mA If t = T/2, then the current in the diode equals: Oa. 15.24 mA Ob. 13.24 mA Oc. 19.24 mA Od. 17.24 mA
From the diode circuit shown below, If E=30 V and RL=802, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 2. D . RL D4 D3 a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
Q-3. Draw 1-V characteristics of 5 V silicon zener diode (Vz-5V) and show its parameters V Vz, Izx. Izs, Izm on the curve. Q-4. Determine the range of Road (Rmin, Rmax) that will maintain Vz at 5 volts for the circuit given below. Rs m 1.0kg V1 40 V Pzm=150mw
#4(a) An 8.2 V (8.2 V at 25 °C) has a positive temperature coefficient of 5.4 mV/°C. What is the output voltage if the temperature rises to 90° C? Page | 4 b) Name two applications of the Zener Diode