using the below circuit;a) calculate Is using kirchoffs voltage law. b)calculate power dissipated by each resistor, and by each source.c)calculte Va, Vb, Vd and Ve.-KnownsEs=10v. R1=1k. R2=2k. R3=2k. R4=1k. V2=10V 4. Using the below circuit.R3R42kVe10v10Va. Calculate Is using Kirchoff's Voltage Law (KVL)).b. Calculate the power dissipated by each resistor, and by each source. c. Calculate VA, VB, VD, and VE.с.

PART (A) : The circuit is : Where, R1=1 kΩR2=2 kΩR3=2 kΩR4=1 kΩ

using the below circuit; a) calculate Is using kirchoffs voltage law. b)calculate power dissipated by each resistor, and by each source. c)calculte Va, Vb, Vd and Ve. -Knowns Es=10v. R1=1k. R2=2k. R3=2k. R4=1k. V2=10V

using the below circuit; a) calculate Is using kirchoffs voltage law. b)calculate power dissipated by each resistor, and by each source. c)calculte Va, Vb, Vd and Ve. -Knowns Es=10v. R1=1k. R2=2k. R3=2k. R4=1k. V2=10V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: Good Design Calculate the unloaded voltage Viua in the following circuit. Record the calculated…

A: Case 1: Calculating no-load voltage i.e. no-load is connected. Applying voltage division rule,…

Q: Assume a 30-ka load resistor is added to the circuit as shown. Calculate the loaded voltage Va.…

Q: -) In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b)…

Q: 1. a) Design a combination circuit that has four LED’s and one resistor. Each LED will be in…

A: We can design the circuit as

Q: True or FALSE A- the source voltage must be equal to the sum of individual voltages across…

A: The explanation is as follows.

Q: For the circuit in the figure, find the following:(a) Equivalent strength(b) The current supplied by…

A: R1, R2 and Voltage source are connected in parallel a)Equivalent strength= equivalent resistance=…

Q: Based upon the following assumptions: V1 = 13V, V2 = 20V, R1 = 1kQ, R2 = 8700, R3 = 3kQ, R4 = 3.2kQ,…

A: The Thevenin’s Voltage in a Thevenin’s equivalent circuit of a network is open circuit voltage…

Q: Calculate the output voltage using the circuit shown. For the resistor components value Rf= 470k…

A: Here the properties of opamp are used to solve it. Kcl is also used here.

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

using the below circuit;

a) calculate Is using kirchoffs voltage law.

b)calculate power dissipated by each resistor, and by each source.

c)calculte Va, Vb, Vd and Ve.

-Knowns

Es=10v. R1=1k. R2=2k. R3=2k. R4=1k. V2=10V

4. Using the below circuit.
R3
R4
2k
Ve
10v
10V
a. Calculate Is using Kirchoff's Voltage Law (KVL)).
b. Calculate the power dissipated by each resistor, and by each source.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the circuit, find Voc by doing KVL around the loop. What is the value of ix. What is the value of Voc. set up the circuit to find Isc. a) What is the value of ix. b) What is the voltage across the 1k-ohm resistor. What is the value of Isc? what is the value of Rth
Draw a easy parallel circuit, using Voltage Source E with 3 resistors. Each resistor has its own voltage drop. a. Write down an equation describing the total resistance (Rt) b.Write the equation describing the source current (Is) c. Write down Kirchoffs Voltage Law for the circuit
Determine the power supplied by the dependent source in the figure.
4. Source transformation
Answer and show the solution.
3. Source transformation
Resistors Circuits I Each of the circuits below consists of a battery and several resistors. Several of the voltages, currents, and resistances are indicated. Use both of Kirchoff's Laws and Ohm's Law to determine as many of the other voltages, currents, and resistances as possible.
Using these diagrams of circuits, what are the steps and materis to create these kind of circuits?
Finding V5 and I5. (Voltage and current )
1. Source Transformation
Determine the current of the circuit below. Then apply Ohm's law to determine the expected voltage drops across R1, R2, and R3. Record these values. Include demonstration of Kirchhoff's Voltage Law. R1 1k 9Vdc R2 220 R3 10k
Assume a 30-ko load resistor is added to the circuit as shown. Calculate the loaded voltage Via. Record the calculated value in the table below. R1 100kO 12V R2 300kO RL Vu 30KO Construct the circuit using MultiSim. Energize the circuit and measure Vi.. Record the measured value in the table below. De-energize the circult. Calculated (V) Measured (V) Parameter VNLI V: Using measured values, calculate the percent voltage regulation for this circuit. VNL1 - VL1 %(VR), = x 100% Calculate the ratio R/R; for this circuit. RL R2