Using the appropriate ACI interaction curves, select the reinforcement of the rectangular short column with stirrups for f'c=4ksi and fy=60ksi. Pu = 300.0 kip Mu = 200.0 kip-ft In the answer to the problem Include the selection of rods, the type of stirrup and the appropriate spacing, the verification of the column size, the verification of the spacing of the rods and the verification of the minimum number of rods. x 15" 20" 2"

Using the appropriate ACI interaction curves, select the reinforcement of the rectangular short column with stirrups for f'c=4ksi and fy=60ksi. Pu = 300.0 kip Mu = 200.0 kip-ft In the answer to the problem Include the selection of rods, the type of stirrup and the appropriate spacing, the verification of the column size, the verification of the spacing of the rods and the verification of the minimum number of rods. x 15" 20" 2"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABCD of negligible weight is initially horizontal, and thesteel rods attached at A and C are stress-free. The 20-kip load is thenapplied and the temperature of the steel rods is changed by ΔT. Find ΔTfor which the stresses in the two steel rods will be equal. Use α=6.5x10-6/oF and E=29x106
7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
Solve for Ay and By with FBD. (Please mention no.of reaction forces in supports for better understanding)
3) A load of 2,700 N acts on the machine part shown below. The machine part has a uniform thickness of 12 mm. Note: Point H will not be used in this problem and may be disregarded. a) Draw an FBD at showing the internal forces present at K. You may choose which side of the part to cut off. One method means you must find reactions at A and B. Choose the method that seems easier to you. b) Calculate the normal and shear stresses at point K (in MPa). [Ans. to check: = 0; ay = -10.89 MPa; Txy=-6.85 MPa] c) Draw the stress element at the point located at K. d) Calculate the normal and shear stresses if you rotate the element -20°. Draw a properly oriented stress element. 2,700 N 135 mm 60° C 50 mm 75 mm 50 mm X 40 mm # 12 mm 15 mm PH 40 mm OK y
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
( Hand written and clean writing )
4.)show complete solution, final answer should be in two decimal only, i will automatically give upvote.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L Figure 1 0.5 L U
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-110 GPa 3P E=200 GPa 7m 3M 80mm 30 mm 30 mm 80 mm 30 mm 30 mm
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.