Answered: Using nodal method, determine the…

Engineering

Electrical Engineering

Using nodal method, determine the magnitude and polarity of the voltage across each resistor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.8P: Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor...

See similar textbooks

Similar questions

A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
What's 15 16 17
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
a. Using Ohm’s Law, compute the voltage and current for eachcomponent. Use the formula Z = Vt / It. b. Compute and record the magnitude and phase angle of the impedanceusing the equation Z= R + RL + jXL – JXC. Use 3uF for the value of C,1.006H for the value of L and for the resistance is computed based onthe specification of the lamp. c. Compute and record for the total power using the formula: Pcomputed = Scosθ d. Compute and record the reactive power and apparent power using theformula Scomputed = V2/ZQcomputed = √S2 − P2 e. Compute for the reactive power (measure) and apparent power(measured) using the formula.Q = PtanθS = P/ cos θ f. Compute the percent difference between the measure and the computedvalue of the impedance.
What's 21 22 23
3&page%3D1 American Uni. Girne American Uni.. O portal.gaueng.org My Profile - Zoom Dashboard My Courses This course Find the Norton equivalent of the circuit 60 30 40V ,50 202 A BI E E E E ere to search
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Exeras: 1. Be rebistance of a sm length of oire is cön sr. Detia) the resitance of an8m longth of the same wire, b) the ength of the seme wine when the res tfonce is 4W s. 2. A Piece f re of crss-cfisndd area 2 muy go0 sr. Finid the rebutance of a wie of the some length and maferial if the crss secfional area s SMm. b). the crosss so area of the wire of the some length ond maeriol of resisfance soD2 3. A oril cons o turns of oopperwirehaving a cm-seton area of 0.8 mmn, The maan Lengtb perfurn is s0 čm anithe nosiãfivity of Cu s 0.02 um. Finh the resistonca of the coil ond pwer absorbed 4. An aluminum wire 7.5m. Lang is consacfed parallel writha copper 201ire de m larg. uhen a curent of rdix passd throngh the Cmibination, iř in fannl tht the curent the aluminung wire ik 3Aup The diamefer of the alumsinum wire is 1,0 mm. Defermane the diamefer of the copper wire. has rebi tance of by the cril when camecfed acm8 110V&c supply?
Ministry of Manpower Directorate General of Technological Education Salalah College of Technology Zlectrical Inginearina Problem - 8 Refer to the circuit below and -25V C2 N. compute the following: i) Total capacitance ii) Voltage across C, iii)Charge across C, iv)Voltage across C5 5 uF C1 5 uF 5 uF C4 5 uF C6 5 uF -16-65V. C5 5 uF (Take V, as 25V) 8-35V VT 25V
What will be the value of the twiddle factor: W42
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559