Using Approximate Methods of Structural Analysis, determine the bending moment, shear force and axial force diagrams corresponding to the two-storey two-bay portal Framed structural steelwork building subjected to both horizontal and vertical loading as shown in Fig.Q2.

Using Approximate Methods of Structural Analysis, determine the bending moment, shear force and axial force diagrams corresponding to the two-storey two-bay portal Framed structural steelwork building subjected to both horizontal and vertical loading as shown in Fig.Q2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A timber wall 75 mm wide, 75 mm deep and 3.50 m high is assumed to be fixed at the top and bottom. It is subjected to uniformly distributed load of 388 N/m acting along the weaker axis of its entire height. The wall is made up of Apitong wood with 80% stress grade with properties as shown: Bending and tension parallel to the grain = 16.5 MPa Modulus of Elasticity in Bending = 7310 MPa Compression parallel to the grain = 9.56 MPa Compression perpendicular to the grain = 2.20 MPa Compute for the following: a) Allowable compressive stress b) Allowable bending stress c) Maximum axial load %3D %3D %3D
A 4-storey with Roof deck AFP armory is to be constructed in Sulu. The facility is essential for the housing of the Philippine Army's newly purchased weapons, ammunitions and explosives. The location of the facility is 7.5 km from the known source which is capable of producing a magnitude 6.7 earthquake. The structure is a Steel MRF with an overall height of 14m from the NGL. The weight per level of the slabs and stairs is equal to 1740 kN. For the walls at the typical levels, the weight is computed as 2362.5 kN and for the parapet at the roof deck level, the weight is computed as 388.8 kN. An equipment 2.0 meters high with a hexagonal cross - sectional area whose sides equal to 1 meter is installed at the second level and has a weight of 100 kPa. Using R = 8.5, which of the following most nearly gives the lateral force at the 4th level in kN? Use Soil Type A.
Find the short term and long term deflections of the type 1 prestressed concrete beam shown in Fig. 8.3. The beam has a rectangular cross- section of 0.3 m × 0.6 m and a effective span of 16 m. 0.1: +0.2 0.24 0.1 4 8 m fc= 50 N/ mrn? 800' KN. Pe- G50 KN
Floor joists 50 mm wide by 200 mm high, simply supported on a 4 m span, carry a floor load at 4.8 kPa. Compute the centerline spacing between joists to develop a bending stress of 8 MPa. What safe load could be carried on a centerline spacing of 0.40 m?
A timber beam 98 mm wide by 160 mm high is subjected to a vertical shear V = 23 kN. Determine the shearing stress developed at %3D layer 3 only 20 mm apart from the top to bottom of the section. Answer must be in MPa.
A 6 storey reinforced concrete building, with a floor to floor height of 4.4m is stabilized by shear wall as with a stiffness, Ecdlc, of 326,779,492 kNm² in the transverse direction. Calculate the maximum vertical load, FV,Ed, in KN that can be applied to the building without it becoming sensitive to second order effects in the transverse direction. It can be assumed that the shear walls are cracked.
Q3) The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m as shown in figure Q3. Using following design data, design main reinforcement for the beam. Design data: The characteristic strength of reinforcement steel (f,) = 500 N/mm? The characteristic strength of concrete is (feu) = 30 N/mm². Diameter of tension reinforcement is 25 mm, Diameter of compression reinforcement is 16 mm if required. Diameter of shear link 8 mm Concrete cover 40 mm, 30.6 kN/m h-370 mm b- 230 mm Section A-A
Q3) The reinforced concrete beam having span of 5 m carrying total design load of 22 kN/m as shown in figure Q3. Using following design data, design main reinforcement for the beam and shear reinforcement for beam. Design data: The characteristic strength for main reinforcement (fy) = 500 N/mm? The characteristic strength for shear reinforcement (fyv) = 250 N/mm? The characteristic strength of concrete is (feu) = 30 N/mm?. Diameter of tension reinforcement is 25 mm, Diameter of compression reinforcement is 16 mm if required. Diameter of shear link 8 mm Concrete cover 25 mm, h- 300 mm 22 kN/m 5 m b- 200 mm Section A-A Figure Q3
For each of the building properties listed below, identify which parameter from the base shear equations shall apply. Building occupancy and function Seismic Base Shear In accordance ASCE-7 code, buildings must be designed to withstand lateral forces that are generated during a severe earthquake. The minimum required design force is given in several equations. Design Base Shear, V= C, W Seismic response coefficient, C,, is the smaller value from two equations: In these equations: C₂ = C₂ < Sp! R Spy R Sor & Spare Seismic Acceleration Parameters from USGS maps is Importance Factor Tis Period of Vibration, (depends on building height & must be calculated) Ris Response Modification Factor from ASCE Table Wis the Effective Seismic Weight of the building. SD1 and SDs, seismic acceleration parameters R, response modification factor I, importance factor T, period None of these
Try to give an adequate answer Civil engineering Q A timber beam 150mm x 250mm deep in c/s is simply supported at its ends and has a span of 3.5m. If the safe stress in bending is 7.5MPa find the maximum safe UDL the beam can carry. What is the maximum shear stress in the beam for the UDL calculated?
when analyzing the stability of an entire frame structure. How would one proceed with the analysis of the structure? What are some of the software you can use to help you do the work within a record time?
A singly reinforced rectangular beam 350 mm wide and 450 mm deep is reinforced with 2-16-mm-diameter bottom bars enclosed with 10-mm-dia stirrups covered with 40 mm of concrete.Calculate the tensile steel strain compatible with concrete strain of 0.003. Use f'c = 26 MPa and fy = 370MPa. Express your answer in 4 decimal places