Use this information to answer Questions 1-8 below. The following table gives data relating a car's fuel efficiency in miles per gallon to its weight in pounds. Weight w (pounds) Fuel Efficiency E (mpg) 37 2100 2200 2400 2500 2800 3000 3200 34 29 27 26 25 23 Question 1 Using the black thread method, a model Elw)-0.014(w - 2250) + 34 was obtained. Find the sum of squared errors (SSE) for this model. Only enter the number, in mog. rounded to two decimal places. 21.51 mpg? Question 2 Using the black thread method, a model Elw) -0.014(w- 2250) 34 was obtained. Find the average error for this model. Only enter the number, in mog, rounded to two decimal places. 1.753 mpg

Q: The crankshaft has loads as shown. Determine the vertical (y-direction) reaction of the bearing at…

A:

Q: 1. The scale is used to measure dirt in a hydraulic system. 2. Probably the greatest problem with…

A: According to the given data in the question    We need to fill the blank 1. The ______________…

Q: Determine the magnitude (N) of the force in member BC  if  F=287N , a=0.44m, b=1.97m, r=1.71m and…

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: Write the two equations of equilibrium, EFx = 0 and EFy !3! %3D

A:

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: 7. 8. is an important part of proper reservoir operation. filters protect a pump from dirt in a…

A: According to the given data 7.________filters protect a pump from dirt in a reservoir. 8.…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: 120 mm 60 mm 90 mn D 80 mm C 45 mim 480 N

A:

Q: /0.009MA BM FOLE 4. Answer:

A: Geometric Dimensioning and Tolerancing (GD&T) could be a language of symbols and measures…

Q: 4. Use F₁ =3, 6₁ = 2, k₁₂₁ = 4₁ K3 = 2,63 = 1, J₁ = 2₁ J₂=5, find the impulse and step response of…

A: Given: To find: Impulse and step response

Q: I start from 2f₁= max, derive to this expression {fy = may, 2) ap(x, y, z) dx (_ ap(x, y, z) ay

A: For the solution refer below images.

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: The force acting on the gear tooth is F=45 KN. Resolve this force into two components acting along…

A: Given, Force acting on gear, F=45KN Free body diagram of the force acting on gear-

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.