Use the Virtual Method to determine thedisplacement of point C and slope of pointPROBLEM #1D of the beam made from steel. I = 245 in“.Express your answer in inches.8 kip8 kipAВDC- 5 ft -5 ft 5 ft5 ft-

The reactions at A and B will be: RA=RB=8 kip (due to symmetry) For EA(x=0 to 5): M=-8x

Answered: Use the Virtual Method to determine the…

Use the Virtual Method to determine the displacement of point C and slope of point D of the beam made from steel. I = 245 in. Express your answer in inches. 8 kip

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use the energy methods, virtual work or second theorem of Castigliano, to find the vertical…

Q: Determine the slope and deflection at the point of the beam (free end) shown by the area moment…

Q: A frame fixed at end 'D' and free at end 'A' is shown in figure. The vertical mm. Assume EI = 16.8 ×…

A: For given arrangement,P=20 kNEI=16.8 x103Frame fixed at D

Q: Draw the deflection diagram of the beam. Then using the double integration method, derive the…

Q: Determine the slope and displacement of point B of the steel beam s

A: Modulus of elasticity (E)= 200 GPaMoment of inertia (I)= 60*106 mm4A Beam system given in the figure…

Q: Problem 1: Determine the slope and the displacement at C. El is constant. Use consistent units, i.e.…

A: E = 29000 ksi I = 1000 in.4 Determine the slope and displacement at C using Conjugate beam method.

Q: sing a method of your choice, calculate the displacement at end D due to the distributed load.…

A: As there are 2 supports B and A and D taht are free ends. At B and C, slope θ but the displacement…

Q: 2. USE VIRTUAL WORK METHOD. Determine the slope (in degrees) and deflection at pointD of the be…

Q: Calculate the slope and deflection at the free end of the cantilever beam shown figure using Method…

Q: Compute the deflection at the tip of the cantilever beam in the figure. Els constant. Given X-290…

A: The given figure is shown below:

Q: Q 2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using…

A: Given Data: Length of beam is L=3 m = 3000 mm. Modulus of Elasticity is E=2.05x105 N/mm2. Moment of…

Q: w= 12 kips/ft 6 kipe D hinge

Q: Compute the slope at point A and deflection at point C of the beam in evious problem using…

Q: 2. A simply supported beam of length L carries a point load P in the downward direction at its…

A: To find the deflection at the mid point. Using 4th order differential equation Virtual work method…

Q: 8. A horizontal beam of unit length under load w(x) satisfies the system: y" = M, M" = w(x), x = (0,…

Q: 25. Consider a simply supported beam. The length of the beam is 6m, distance from the left support,…

A: The deflection is the amount to which the structure displaced due to the applied load on the…

Q: ) Using these results (δ1=0.1097 in. , δ2=0.1265 in. , δ3=0.0548 in.) determine the deflections of…

Q: Show FBD

Q: Use Castigliano's Theorem to determine the vertical displacement at joint B in mm. Cross sectional…

Q: Determine the displacement at point C by P A

Q: Use the Castigliano's theorem to determine PROBLEM # 2 the displacenment of point C and slope of…

A: By placing a load P at the point C downwards. Finding the support reactions. Take the moment about…

Q: Using an algebraic summation of components, calculate the resultant R of forces A, B and C. Find…

A: Horizontal component :Rx=-200442+32+170882+152Rx=-80NVertical component…

Q: 5061/in 800 Ib/in. H. 9 in. Point C is the midpoint of beam BH. Find the deflection of point C,…

A: Step 1

Q: From the figure, the beam used has the following properties: L = 2 m, E 200 GPa and I = 200 x 10° mm…

A: a.) The expression for maximum deflection of the beam is given as…

Q: Calculate the value of the deflection at point C. Enter your answer in mm to three decimal places.…

A: Given:Required:Deflection at C

Q: Determine the magnitude(lb) of the vertical component of force at point C if P = 151 lb, x = 13.2…

Q: Calculate the moment of inertia of the cross section of the beam about its centroidal xo-axis.…

Q: The beam is loaded as shown. Determine the slope at the left free end. (at point A) in radian. Use…

A: given Data, L= 7m q=20KN/m Note: In the span AB ,the total UDL load is converted into the Point load…

Q: Q2- For the frameshown in the figure determine the total displacement of join A if support C…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: At 日 a1/3 L/3 エ 2エ

Q: Assume a constant value of EI = 560×10° N-mm² for the beam. 210 N-m 200 mm Determine the deflection…

A: A simply supported beam is loaded as follows with EI=

Q: . Find the deflection of the be

Q: Double Integration The given averhanging beam is loaded as shown. Use E = 1.5 x 10*6 psi andl = 40…

Q: Q2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using…

Q: Determine the deflection at points B and C of the beam shown. Values for the moment of inertia of…

A: Given data E=200Gpa= 2×105 N/mm2IBC=I=4×106 mm4IAB=2I=8×106 mm4EI=2×105Nmm2×4×106mm4EI=8×105 N-m2…

Q: Calculate the deflections in B, which is in the middle of the central section, using the CONJUGATE…

Q: For the beam shown, calculate the beam slope at A. Assume that a = 77 in., b = 264 in., c = 87 in.,…

A: Given data: a = 77 in. b = 264 in. c = 87 in. w = 0.37 kips/in P = 6 kips, and EI = 1336000…

Q: The beam is loaded as shown. Determine the slope at the left free end. (at point A) in radian. Use…

A: ∑MB=0⇒RC (10)=60×15⇒RC=90 KN⇒RB+RC=60+60⇒RB=120-90=30 KN…

Q: Q2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

Use the Virtual Method to determine the
displacement of point C and slope of point
PROBLEM #1
D of the beam made from steel. I = 245 in“.
Express your answer in inches.
8 kip
8 kip
A
В
D
C
- 5 ft -5 ft 5 ft
5 ft-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the horizontal displacement in mm, up to 4 places of decimal with correct sign
For the given problem use the conjugate beam method to determine the slope and deflection at point A and also the maximum deflection of the beam. Use I = 1500 in. and E = 29x106 psi. 30 k A 12 ft 24 ft
Please show all steps.
Determine the magnitude(lb) of the vertical component of force at point C if P = 137 lb, x = 14.7 in, y = 8.3 in, and z = 7.5 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use U if upward and D if downward.
Using Virtual Work Method, Compute the deﬂection at B and the slope at A in the Figure. EI is constant. Express the slope in radians and the deﬂection in inches. E = 29,000 kips/in2, I = 2000 in2. "Length is in Feet"
Given a cantilever beam of length L=4.3meters. The left support “A” is free while the right end “B” is fixed. With constant EI=19000 KN-m2 A downward concentrated load of 47KN is applied at “A”. Using Double Integration Method (DIM) with origin taken at point A where 0 ≤ x ≤ L, calculate the deflection at midspan? Express your answer in "mm" in 2 decimal places. Include (-) negative sign if deflection is downward.
Using Conjugate-Beam Method, determine the displacement at B. 12 m I 80 KN B E = constant = 200 GPa I=600 (106) mm² 12 m 21
Determine the displacement and slope at point C of the cantiveler beam. The moment of inertia of each segment is indicated in the figure. Take E=200GPa. Use Castigliano's theorem.
Given a cantilever beam of length L=2.1meters. The left support “A” is free while the right end “B” is fixed. With constant EI=19000 KN-m2 A downward concentrated load of 70KN is applied at “A”. Using Double Integration Method (DIM) with origin taken at point A where 0 ≤ x ≤ L, calculate the deflection at midspan? Express your answer in "mm" in 2 decimal places. Include (-) negative sign if deflection is downward.
Using Virtual work method (unit load)
A beam is loaded as show in the figure. Assume EI is constant. Using Virtual Work Method determine the following. A. Deflection at C B. Slope at E
Calculate the beam deflection at point C. Negative if deflection is below the x-axis and positive if above. Assume that E = 29,000 ksi and / = 836 in.4 are constant. Answer in inches rounded-off to 3 decimal places 45 kips 4 kips/ft 8 ft B 11 ft 11 ft X