Use the Castigliano’s theorem to determine the displacement of point C and slope of point D of the beam made from steel. I = 245 in4Express your answer in inches. Use the Castigliano's theorem to determinePROBLEM # 2the displacement of point C and slope of pointD of the beanm made from steel. I = 245 in4.Express your answer in inches.8 kip8 kipAВD- 5 ft+ 5 ft--5 ft -- 5 ft-

By placing a load P at the point C downwards. Finding the support reactions. Take the moment about…

Use the Castigliano's theorem to determine PROBLEM # 2 the displacenment of point C and slope of point D of the bean made from steel. I = 245 in4. Express your answer in inches. 8 kip 8 kip A В D C - 5 ft- - 5 ft -5 ft 5 ft-

Use the Castigliano's theorem to determine PROBLEM # 2 the displacenment of point C and slope of point D of the bean made from steel. I = 245 in4. Express your answer in inches. 8 kip 8 kip A В D C - 5 ft- - 5 ft -5 ft 5 ft-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is subjected to equal bending moments of M₂ = 4200 N·m. The cross-sectional dimensions are b = 110 mm, c = 33 mm, d = 74 mm, and t = 3 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Answer: (a) y= i M. mm 1₂ = i mm4 S= i mm³ (b) OH = i MPa (c) OK = i MPa (d) Omax = i MPa (typ) b H K
Convert from english to to metric units. Show your step by step answer with solutions
Determine the slope at the left support A (in degrees.). The beam is loaded with a moment load M = 15 kN-m at its midspan. EI is constant and equal to 36,159 kN-m^2. Use length of beam L = 8 m. ROUND OFF TO FIVE DECIMAL PLACES. USE STORED VALUES.
Solve using Castigliano's Theorem
A concentrated load P = 5 kN, acting downwards, is located midway between the simple supports of the beam shown. Determine the deflection, in mm, at the free-end C. Use a = 6 m., E = 239 GPa, and I = 271 x10^6 mm^4. ROUND OFF TO THREE DECIMAL PLACES. USE STORED VALUES. INCLUDE THE SIGN OF YOUR FINAL ANSWER. (positive = upwards; negative = downwards) A a a
Determine the horizontal displacement of joint C using Castigliano's theorem. Each steel member has a cross-sectional area of 500 mm 2 E= 200 GPa 8 KN C 2 m D 18 KN 1.5 m B
Determine the slope at the left support A (in degrees.). The beam is loaded with a moment load M = 17 kN-m at its midspan. El is constant and equal to 33,334 kN-m^2. Use length of beam L= 7 m. ROUND OFF TO FIVE DECIMAL PLACES. USE STORED VALUES. INPUT THE VALUE ONLY A
Problem 5 Using the conjugate-beam method, determine the displacement at D and the slope at D. Assume A is fixed support, B is a pin, and C is a roller. Take E = 29×10³ ksi, I = 650 in ¹. 12 ft- B -12 ft Ic 12 ft- 24 k
PLEASE SOLVE THIS ONE AS SOON AS POSSIBLE AND SURELY I WILL RATE U. THANK YOU (STEP BY STEP PROCESS)
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
A beam is subjected to equal bending moments of M₂ = 4300 N·m. The cross-sectional dimensions are b = 120 mm, c = 33 mm, d = 67 mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Answer: (a) y= i mm M 1₂ = i mm4 S= mm³ (b) OH = i MPa (c) OK = i MPa (d) gmax= i MPa (typ) b H K
A concentrated load P = 9 kN, acting downwards, is located midway between the simple supports of the beam shown. Determine the deflection, in mm, at the free-end C. Use a = 6 m., E = 219 GPa, and I = 256 x10^6 mm^4. ROUND OFF TO THREE DECIMAL PLACES. USE STORED VALUES. INCLUDE THE SIGN OF YOUR FINAL ANSWER. (positive = upwards; negative = downwards) P A