USE IMAGE BELOWQuestion; draw and fully label the Freebody diagram of the BEAM in the picture below. ### Diagram Explanation: Inclined Beam with Distributed LoadThis diagram represents an inclined beam configuration subjected to a uniformly distributed load. The details of the diagram are as follows:- The beam is inclined at an unspecified angle but is supported at two points, denoted as points A and B.- Point A is located 1 meter from the left end of the beam. This point provides a pivot-like support.- Point B is located at the far right end of the beam, 3 meters from point A. This point provides a base support.- The total length of the beam from the left end to point B is 4 meters.- The beam is under a uniformly distributed load of 800 N/m acting downwards along its length.- The vertical distance between the base of the beam's slope and a horizontal line through point A is 3 meters.#### Key Measurements:1. Inclination height: 3 meters.2. Distance from the left end of the beam to point A: 1 meter.3. Distance from point A to point B: 3 meters.4. Total length of the beam from left end to point B: 4 meters.5. Uniform distributed load: 800 N/m.The downward arrows along the length of the beam depict the direction and nature of the distributed load. The diagram is essential for understanding concepts related to beam dynamics, load distribution, and structural support analysis.

Answered: Image /qna-images/answer/948cfb2d-e9d4-4386-bccd-529ef24f0798.jpg

Answered: USE IMAGE BELOW Question; draw and…

Engineering

Mechanical Engineering

USE IMAGE BELOW Question; draw and fully label the Freebody diagram of the BEAM in the picture below.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the moment of inertia about the x axis.
For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present, and that at the other end of the column a counter-clockwise moment of 25 k-ft is present. You may assume that K=1.
For the beam in Fig. (a) Draw the free-body diagram and calculate the reactions.(b) How many runs of analysis are required to compute the internal forces?(c) Calculate the internal forces (mathematical expressions) and graph them. Don't forget to draw the free-body diagrams used to derive the internal forces.
[Q+](problem 3/17P133) رسم لسئؤال The uniform beam has a mass of (180 kg). Compute the reactions at the 1.4 kN 3 kN B. A 0.6 m Hint, put Wat point A 0.6 m "o". 1.8 m 0.6 m 30 pin o,
Draw (FBD) and calculate the support reactions in the simply support beam ABCD below 0.3m B 3kN 0.5m 1.2m 5kN Lo ** 60⁰ 0.4m
Subject :- mechanical engineering
The distribution of loads in a simply supported beam is as given in Figure 2. D. Calculate reactions at the supports.
LAai ple J Draw the S.F. and B.M. diagrams for the beam loaded as shown in Figure (3). combination of concentrated loads and uniform distributed loads. Consider the beam shown in the Figure below loaded with a 20 kN/m 10 kN/m 20 KN 10 kN 40 kN 20 kN F -2m -2m- RA RE Figure (3)
For each of the beams below draw the FBD, V diagram, and M diagram.
Pin-joint construction supports point loads as shown below: P Al ΕΙ C B 2/3 L 1/3 L a) Find the equation for the deflection of the bar at point B! b) Determine the equation for the moment that occurs at point A!
This question is made of two separate parts related to figures 1 and 2. 2 m F Figure 1 2 m in A direction L direction Figure 2 Figure 1 D A beam AB is supported by a pin at A and a roller at B. The beam is subjected to force F of 5 KN, making an angle a=400 with horizontal as shown in figure 1. The support reaction at pin A along x-axis is to the The support reaction at pin A along y-axis is The support reaction at roller B is M B Figure 2 A beams AB of length L-2 m is supported by a pin at A and a cable BC at point B. The beam is subject to an external moment M=200 N.m at B as shown in figure 2. The force in cable BC is and it is in
For the structural beam loaded and supported as shown in Figure 2, (a) Draw a free body diagram and find the support reaction forces/moments.