use force methodConsider the beam shown below. The structure is subjected to two concentrated loads.If all three supports settle the followingamounts: A = 4.0 in., B = 2.0 in., and č= 3.5 in., determine the supportreactions and draw the bendingmoment and shear force diagrams.60k90k10 ft 10 ft10 ft 10 ftNote: E = 4,000 ksi, / = 1200 in"; selectthe reaction at Support B to be the redundant.

Solution- We have a beam in the question with two focused loads; we must determine the following.The…

use force method Consider the beam shown below. The structure is subjected to two concentrated loads. If all three supports settle the following amounts: A = 4.0 in., B = 2.0 in., and C = 3.5 in., determine the support reactions and draw the bending moment and shear force diagrams. 60 k 90k F10 A-10 ft–10 ft 10 f - Note: E = 4,000 ksi, /= 1200 in"; select the reaction at Support B to be the redundant.

use force method Consider the beam shown below. The structure is subjected to two concentrated loads. If all three supports settle the following amounts: A = 4.0 in., B = 2.0 in., and C = 3.5 in., determine the support reactions and draw the bending moment and shear force diagrams. 60 k 90k F10 A-10 ft–10 ft 10 f - Note: E = 4,000 ksi, /= 1200 in"; select the reaction at Support B to be the redundant.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bridge girder AB on a simple span of length L = 30 m supports a distributed load of maximum intensity q at mid-span and minimum intensity q/2 at supports A and B that indudes the weight of the girder (see figure). 450 mm 32 mm B 30 m 16 mm- 1800 mm 32 mm 450 mm The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q (in kN/m) based upon the following. (a) solely based on an allowable bending stress aallow = 110 MPa kN/m (b) solely based on an allowable shear stress tallow = 50 MPa kN/m (c) accounting for both an allowable bending stress ollow and an allowable shear stress Tallow kN/m
A simply supported beam is 0.6 feet long, and has a distributed load of 8.9 kips/ft pointing in the negative y direction along the entire beam. First- find the maximum moment in the beam? HINT: You should draw the beam. QUESTION: If the y distance from the neutral axis to the furthest fiber in tension is = -5 inches, and the moment of inertia of the beam is 100 in4, then what is the bending stress in the beam? in psi? Give answer to 1 decimal point, and no units, such as 1250.1 (not 1250.1 psi)
STATICS OF RIGID BODIES Three wheel loads rail as a unit across a 12m span. The loads are A-10kn, B-20kN to the right of A; and C-40kN to the right of B. Determine the magnitude of the resultant and show the distance from point A.
Pls help me.
Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through the centroid, the line of action is inclined at (30°) to the vertical direction. Calculate the maximum bending stress at mid-span, and locate the neutral axis. Neglect the weight of the beam. nax Bending 4 KN ➜g N 30⁰ 80 8 mm 160- 25=2 200
An over hanging beam ABC of length 10 m (including over hang portion) is shown in the figure below. The ratio of ILD ordinates at C to ILD ordinates at B for the shear force at B is A B 7 m 3 m-
I need the carrect answer as soon as possible
NEED IN 1 HOUR PLEASE THANK U A hollow steel shaft 10 ft long must transmit a torque of 250,000 lb-in. The total angle of twist in this length is not to exceed 2.5 degrees and the allowable shearing stress is 12,000 lb/sq.in. Determine the inside and outside diameters of the shaft if G = 12 x 106 lb/sq.in. The action is elastic.
Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through the centroid, the line of action is inclined at (30°) to the vertical direction. Calculate the maximum bending stress at mid-span, and locate the neutral axis. Neglect the weight of the beam. nax Bending 4 KN ➜g N 30⁰ 80 8 mm 160- 25=2 200
Provide solution and mention all steps
stresses in beams 3.
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance %3D either up or down. For a loading of w = 5.4 kips/ft, determine: (a) the beam deflection vg at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBc = 7 ft, LcD =7 ft, LDE = 6 ft. %3D A B E LAB LBC LcD LCD Lpe Answers: (a) VA = -0.65669 in. (b) vc = 0.024937 in.