Use an elastic analysis and determinethe maximum load per inch of weld.Use LRFD.70 kips/75°3",3",3",6"13"l'-0"6"9"

LRFD It applies Ultimate factored loads to design. Evaluate forces and stress using yielded…

Answered: Use an elastic analysis and determine…

Use an elastic analysis and determine the maximum load per inch of weld. 70 kips/ 75° "3",3", Use LRFD. 1 3" 6" l'-0" 6" 9"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused…

A: Solution: Diagram of Welded Connection If no eccentricity is there:Calculate the Direct shear…

Q: app 3.0. Investigate all limit states. The tension m gusset plate is A36. The weld is a 1/8-inch fil…

Q: Determine the maximum resultant stress on the 20mm fillet weld. L1 = 200mm, L2 = 250mm & L3 =…

A: Answer:

Q: 37. Determine the available strength of a WT7×15, A992 steel, with the flanges welded to a 1/2 in.…

A: Given: Section: WT 7 x 15 (A992 steel) Length of weld: lw1=5 in lw2=11 in To find: Considering…

Q: The billboard post support a 5KN dead load as shown. The cantilever beam and the brace is pinned…

A: Answer (a) Calculation of ultimate force the brace carries Since the connection is pinned let us…

Q: 4 - The riveted type connection will be used to assemble the given steel members. Determine the safe…

A: Crushing stresses: The compressive stresses at the surface area of contact between the two…

Q: A C9x20 is used as tension member connected to a gusset plate of ½ in thick (Figure 4). The member…

A: DL = 40kips LL = 80ips Thickness of the gusset plate = 12in. Steel used A36

Q: Q2For the gable frame shown in fig. below, roof dead load = 60 KN/ m. Determine total static load…

A: Given:- The total dead roof load = 60 kN/m The length at the point A and B = 6 m The length at the…

Q: One leg of an 8 x 8 x 3/4 angle is to be connected with side welds and a weld at the end of the…

A: Fillet weld: This weld is a joint made by joining two metal pieces together which are perpendicular…

Q: Determine the maximum load in the weld in kips per inch of length.

A: Given:- welds To find:- Maximum load

Q: A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Determine the adequacy of the hanger connection in Figure Account for prying action. a. Use LRFD. b.…

A: Question is based on hanger connection . Value of dead load , Live load and other dimensions are…

Q: ISA 70*45*6 mm Leg connected=45 F=350KN Gusset plate=10mm

A: Working load= 350kN Factored load= 350kN×1.5=525kN Hence each angle carries a factored pull of…

Q: The PL 18 x 1/2 as shown below are connected to PL 50 x 1/2 in with longitudinal SMAW fillet welds…

A: PL 18 X 1/2 connected to PL 50 X 1/2 Fillet weld 7/15 in fy = 50 ksifu = 65 ksiElectrode = E70

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Question is based on hanger connection . Value of dead load , Live load and other dimensions are…

Q: Two 3/16" E70 fillet welds of 15 in. Iong are subjected to a load P. Using LRFD, compute the…

A: Answer (a) Minimum weld length requirement Minimum weld length may not be less than 4 times the…

Q: PROBUEM A : US ING METHOP of SECION, SOLVE FOR THE RCES ACHNG ON MEMBERS BD, BE AND E, INDIGATE…

A: Given: The value of P1 is 3 kN. The value of P2 is 8 kN. The value of P3 is 4 kN. The angle θ is…

Q: Repeat Prob. 14-4 if 1/4-in welds are used and if θ = 45°. Prob. 14-4: Determine the LRFD design…

A: Calculate the LFRD design load and ASD allowable load for the given connection:

Q: a. Use LRFD and design a welded connection for the bracket shown in Figure . All structural steel is…

A: Solution; (a) By allowable stress design: Calculate Factored load coming ion connection. Pa=D+L…

Q: Design a Bolted connection between member B-C and B-A if B-C section is W310x86 and B-A is W310x86…

A: Designing a Bolted Connection for Member B-C and B-AUnderstanding the ProblemWe are tasked with…

Q: Q5. What is the minimum clearance required by OSHA regulations between a crane and a 150-kV power…

A: The Occupational Safety and Health Administration(OSHA)-The Occupational Safety and Health…

Q: Repeat Prob. 15-11 using SMAW shop and field welds Prob. 15-11: Select a framed beam connection,…

A: Compute factored loads for LRFD by using the load combination if dead load is 45k and live load is…

Q: Rework Prob. 14-25 if the load is increased from 40 to 60 k and the horizontal weld lengths are…

A: a} Use elastic method Consider the setion Assume a 1-in well as in figure Calculate the area of the…

Q: 2. Problem 7.8-2 Determine the adequacy of the hanger connection in Figure P7.8-2 Account for prying…

A: Flange thickness bf = 4+4+38Flange thickness (bf) = 8.375 inWeb thickness tw = 38+58…

Q: Why is the process of measuring excavation different from measuring the work of other trades?

A: Solution: The process of measuring excavation is generally different from measuring the work of…

Q: Perform the following for the moment connection from a W18X46 to a W14 column below. Assume that the…

Q: Q1 Two 3/16" E70 fillet welds of 15 in. long are subjected to a load P. Using LRFD, compute the…

A: Answer We are given size of weld (w)= 3/16 in Length of weld L = 15 in E 70 electrode

Q: How to layout simple curves by Deflection Angles? Outline the step by step process and show a…

Q: 10/10 find the tensile stress in upper plate in section 3-3 2 1 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN…

Q: 1R@ T =108'

A: Factored load is the load at which the structure obtains a collapsed zone, that is, it is unable to…

Q: Q2. A tie member of a roof truss consists of two angles are connected to either side of a gusset…

A: Working load= 350kNFactored load= 350kN=525kNHence each angle carries a factored pull of kN

Q: Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).

A: Given:- The magnitude of the load = 15 k To determine:- The maximum load in the weld (in kips per…

Q: If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity…

Q: Determine the required weld size necessary to carry the load P.

A: Solution Dead load(PDL)=360 kN Live load(PLL)=120 kN The centroid of the area is, x=1502=75…

Q: The torque (C) to be transmitted by a drive at the welds is 650 Nm. Knowing that the diameter of the…

Q: A WT6x15 shape made from A36 steel will be welded along its flanges to a gusset plate.…

A: The objective of the question is to determine the LRFD available strength for gross tension yield of…

Q: Consider the connection is welded with 7/16 in. welds with FEXX =70 ksi as shown. The channel…

Q: A joist cutting is used as a bracket to support a load of 135 kN. It is welded to the column flange…

Q: P6.11-8. (a) Determine the moment of inertia I and the section modulus S for the modified beam.…

A: Given, W200×59 steel wide flange beam175 mm×10 mm platesqallow=400kN/mTo determine,Moment of interia…

Q: Problem 3. An un-equal leg angle L8x4x½ made of ASTM A242 steel (Fy = 50 ksi, Fu = 70 ksi) is used…

A: Unequal leg angle, L 8 x 4 x 1/2" of ASTM 242 steel, Fy=50 ksi , Fu= 70ksi To Find: (a) Factored…

Q: ickness (S=5/8") with "A36" member steel (fy=36 ksi & fu=58 ksi).

Q: A C130x10 tension member is welded to a plate as shown in the figure. The channel is of Grade 350W…

Question

Use an elastic analysis and determine
the maximum load per inch of weld.
Use LRFD.
70 kips/
75°
3",3",3",
6"
13"
l'-0"
6"
9"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

9. Determine the service load capacity assuming the load is 70% live load of the tee connection as shown in Figure 6.28 and details the proper double-bevel-groove weld for the SMAW process. Assume the flange of the tee does not control design. R-3×8 (A36 Steel) 128 kips Problem 164 164 kips Solution E60
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae
1- The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of shear stresses. (St-37, H) t= 20 # ##* JL 90.90.9 40 50 315 9,96 t 9,04 t 9,40 t 9,70 t
Find the size of E70 fillet weld required for the shear and tension connection shown. Use the following details: P = 250 kNe = 130 mmb = 150 mmd = 200 mmAssume the column and bracket plate does not control the strength.
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
14-11. Design by LRFD and ASD maximum size side SMAW fillet welds required to develop the loads PD = 70 k and P₁ = 60 k for an L6 × 4 × 1/2, using E70 electrodes and 50 ksi steel. The member is connected on the sides of the 6-in leg and is subject to alternating loads. (Ans. L₁ = 12.5 in, L₂ = 6.5 in (LRFD); L₁ 13.5 in. L₂ = 7.0 in (ASD)) =
Compute the nominal strength based on yielding in KN. Determine the allowable tensile strength of Plate A in KN. Compute the allowable tensile strength at section a-1-2-2-4-c in KN.
Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material :fy = 480 MPa, fu = 560 MPa, Members are S235) a Section a-a 10 mm 10 cm P { =37.14 mm 5 cm 16 mm Gusset Plate a
Using SMAW process, E70 electrodes and an A572 steel. Determine thelength of the side fillet welds for the full capacity the 125x100x10mm angle tensionmember as shown below. Assume that the member is subjected to repeatedstress variations making any connection eccentricity undesirable. Check theblock shear strength of the member. Assume that the WT chord has sufficientstrength to develop the weld strengths and the thickness of its web is 12mm. UseU = 0.87 for class use and LRFD Method only.
For the bracket connection shown in the figure, determine the design strength in kips of the connection
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
• Compute the available block shear strength of the connection based on the KN. (Diameter of hole is 20mm, ST37 steel is used, and thickness of plate is 7.5mm) 2@75 mm 3@75 mm