Uniformly Tapering Cylindrical rod For an uniformly tapering cylindrical rod subject to tensile load, the expression for resulting elongation due to the tensile stress is given as, 4PL SL A ED,D, Load applied Length of the cylinder Smaller diameter of the cylinder Larger diameter of the cylinder Young's modulus of the cylinder material where P L D1 D2 E

Q: 100NM rod-1 100N rod-2 toost took 0.75 0.50 rod-1 0. rod-2

A:

Q: 34+ 20°c, arigid slab is supported. as shown. At what temperature. the stress in the steelrod will…

A:

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

A:

Q: ild steel rod having a stress of 50 Mpa and having a diameter of 20 mm  What is the force applied

A: Given:Stress, σ=50 MPadiameter, d=20 mm

Q: 2. A bronte bar is fastened between a steel bar and an aluminum bar as shown in Figure. Aaial foads…

A:

Q: The 0.06R (mm)-diameter bar is made of a brittle material with the ultimate strengths of 0.15R MPa…

A: d=.06R mm where R=993 d=.06×993=59.58 mmσut=.15R Mpa σut=.15×993 Mpa=148.95 Mpa Bending moment and…

Q: A round cross-sectional bar d= 30 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a…

A: The ultimate tensile strength (UTS) of a material is the highest stress it can withstand when…

Q: walled vessels is assumed to apply? ssure found in part (a), compute the s

A:

Q: A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16…

A: Rod specimen

Q: The figure depicts a filleted cantilever bar. Find the largest normal stress for two cases: (a) the…

A: Given data: P=400 NM=10 N.mb=12 mm Need to determine the largest normal stress.

Q: sectional bar d= 39 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a completely…

A:

Q: A round cross-sectional bar d= 32 mm is cut from steel of Sut = 715 MPa. The bar is loaded with a…

A: d = 32 mm Sut = 715 MPa Se = 350 MPa

Q: ) Derive the flexure formula for the straight members?

A:

Q: (B) – Figure Q4/B show the bone has an outer rac of 15 mm and thickness 3 mm. Determine the strains…

A: Draw the diagram for the axes given in the problem. Understand that in the given figure, the shaft…

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

A: Q) Given data         σx = 170 MPa        σy = 90 MPafor AISI 1020  carbon steel σyt = 350 MPaTo…

Q: Torsional moments affect the rods as shown in the figure. a- Draw the torque diagram on the rod.…

A: Given data: For steel pipe: do=10 cm=100 mm ; di=5 cm=50 mm ; GSt=83 GPa ⇒Polar moment of inertia of…

Q: Design a knuckle joint to two connect two co-axial steel rods with 45C8 (S= 380 N/mm) to support a…

A: given data

Q: In Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data: The diameter of part AB is dAB=100 mm The diameter of part BC is dBC=80 mm The length of…

Q: FIND THE AREA USING SODERBERG PRINCIPLE

A: Given data; P1=20 kNP2=100 kNσyt=240 MPaσe=160MPaF.O.S=2

Q: The average circumferential stress

A: Given data;   Thin cylinder of ,Inner radius , =500 mmThickness= 10 mmInternal pressure=5 MPa We…

Q: s shown in Figure Q1. Dimensions th of 90 MPa. The diameter of the etion at A:

A:

Q: Q1/ A two circular bars of brass (AB) and steel (CD) in horizontal state with gap of (1.5min)…

A:

Q: Figure 1: This bar is made of AISI 1020 cold-drawn steel and is loaded by the forces F=60 lb, F2= 80…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

A: Given Data  σx = 199 MPa σy = 76 MPa

Q: hardest point in the embedment A or B of the element shown in the figure. This bar is made of hot…

A:

Q: A rectangular post which is made up of two blocks of wood glued together along a joint inclined at…

A:

Q: 1. A rigid horizontal bar of negligible mass is connected to two rods as shown in the figure. If the…

A:

Q: The figure below shows the stress-strain behavior of a mild steel (the insert shows part of the same…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given:di=5mmE=120 GPaμ=0.33df=4.995 mmLet li anf lf be the initial and final length of the…

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: Torsional moments affect the rods as shown in the figure. a- Draw the torque diagram on the rod.…

A: Torque is the turning effort caused due to the force. The torque diagram represents the loading…

Q: A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.75 m long and…

A: The above question is based on Torsion due to Torque which is applied at the ends.

Q: The bar in the figure with a diameter of 25 mm and a length of 1000 mm is made of Ti6Al4V alloy. A…

A: Torsion Torsion is the twisting of an object due to an applied torque.   Torque  Torque is the…

Q: ) Derive the flexure formula for the straight members?

A: Stresses caused by the bending moment are known as flexural or bending stresses. Consider a beam…

Q: (3X) A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram…

A: Stress-Strain curve gives the idea of the material to carry a load or the behaviour of the material…

Q: Consider the bar in Figure 2 loaded as shown. Determine the nodal displacements, stress in each…

A: Given:To find:(a) Nodal displacements.(b) Stress in each element.(c) Support reaction.

Q: A solid 2 inch diameter bar is experiencing a torque of 3000 in-lb. The material of the bar has a…

A: Torsional Shear Stress Calculation:The first step is to calculate the torsional shear stress in the…

Q: A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14…

A:

Q: 8. A steel 0.6 inch x 1.2 inch steel 90 m long is subjected to a 4500 Ibs tensile load along its…

A: Given, W = 0.6 in T = 1.2 in A = 0.72 in2 L = 90 m = 3543.3 in P = 4500 lbs μ=0.3

Q: A two-bar system has the configuration shown in the Figure Q1 below. The cross-sectional area for…

A:

Q: PROBLEM 4. The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4…

A: