Uniform Chemical Heat Generation. Heat is being generated uniformly by a chemical reaction in a long cylinder of radius 91.4 mm. The generation rate is constant at 46.6 W/m³. The walls of the cylinder are cooled so that the wall cemperature is held at 311.0 K. The thermal conductivity is 0.865 W/m · K. Calculate the center-line temperature at steady state.

Q: A refrigeration system with a capacity of 10 tons of refrigeration operates at 210 kPa in the…

A: Given data: Capacity of refrigeration = 10 ton Temperature in evaporator = 210 kPa Temperature in…

Q: The flat wall given below is formed by the series and parallel arrangement of layers A, B, C, D and…

A: Given Data  A composite wall is formed by series and parallel arrangemnt of plates  The…

Q: I at 351 v.v42L i) Calculate the temperature distribution at the middle and rate of heat floe at the…

A: Given,

Q: - Using the phase diagram for phosphorous below, which of the following statements is correct?…

A:

Q: Steel pipe 1 cm thick, 1.0 m long and 5 cm deep, covered with 2 cm thick insulation. The wall…

A:

Q: Find all letters, answer for a and b are 39.27 W and 93.7 degrees Celcius Heat is conducted through…

A:

Q: 2. Heat is transferred steadily in one direction in a composite plane wall that is made of two…

A: The objective of this question is to determine the rate of heat transfer in the system and the…

Q: A certain material has a thickness of 4 cm and its thermal conductivity is 0.04 W / m.oC. At a…

A: The heat flow rate at the given distances from the material is to be calculated.

Q: Inner and outer diameters of 12 pipes used in a one shell one pass horizontal condenser are 2.2 cm…

A: Given: Hot fluid: Th = 60 oC mh = 0.045 kg/s hf = 2366 kJ/kg Cold Fluid: Tc1 = 20 oC mc = 6 kg/s…

Q: (3.4) The gas heater shown below in cross-section consists of a square sheet-metal duct insulated on…

A: a) given = Heat transfer fluid data T1 = 500 K T2 = 450 Kh1 = 200 W/m2K f1 = 0.00035 m2K/w Process…

Q: The energy transfer between the hot fluid and cold fluids is brought about by their complete…

A: We have to answer which type of heat exchanger is used where the hold and cold fluid is direct…

Q: A polished stainless steel surface is electrically heated form the bottom to boil water at…

A: Material = Polished stainless steelPressure, Temperature,

Q: The aim is to reduce the thickness of the first steel wall. Between the two walls there is a…

A: Given : Height Thickness Width Expansion rate Weight of wax

Q: Straight metal fins (k = 45 W/m °C) of triangular profile installed on a 1 m × 1 m wall The wall is…

A:

Q: The exhaust duct from a heater has an inside diameter of 114.3 mm with ceramic walls 6.4 mm thick.…

A: Given data: Inside diameter = 114.3 mm Ceramic walls 6.4mm, the average k = 1.52W/mKThermal…

Q: In a desert chemical plant, the operator wishes to store chilled water underground in a spherical…

A:

Q: Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm…

A: Given, Diameter of pipe, D = 100 mm×1 m1000 mm    = 0.10 m temperature on outside surface of pipe,…

Q: A long circular cylinder is encased and centered in a long square cylinder of concrete (k 1.2 W/m·K)…

A: Given , Thermal conductivity,k=1.2W/mKTemperature of cylinder,T1=200°C=473KTemperature of…

Q: 1. An experimental engine has a quartz window in the cylinder head that is 2.5 cm thick. During…

A: The heat transfer process is a process in which the molecules are moved from the region of higher…

Q: Q2. An annulus consists of the region between two concentric tubes having diameters of 3 cm and 5…

A:

Q: 3- Calculate heat transfer flux of a wall with two layers of insulations. The inner wall is at…

A: The heat transfer flux for the given insulation system is to be determined.