Under CSI Format, explain the difference between the documents referred to as “General Conditions” and “General Requirements.”

Q: Given the tabulated data for a closed traverse in which the bearings of BC and the length of EF have…

A: Closed traverse survey data is given in tabular form and it has been asked to determine missing…

Q: Show complete solution. Draw all necessary diagrams / illustrations. Using elastic method, compute…

A:

Q: 3. Influence lines for trusses. The bridge truss shown in the figure is to be subjected by uniform…

A:

Q: Uniform, and Non- uniform flow

A: uniform flow= when parameters of fluid like velocity and depth etc. won't change with space at any…

Q: A 30m tape is supported only at its ends and under a steady pull of 8kg. If the tape weighs 0.91 kg,…

A: Introduction- The Tape correction(s) in surveying refers to the process of adjusting measurements…

Q: "Repository, modelling tool, documentation instrument, engineering instrument, and construction…

A: 1. Repository A repository is a central location where data, information, or software code can be…

Q: Problem 2 A transit with a stadia interval factor of 100.8 was set up at C with elevation of 548 m.…

A: Tacheometric surveying is used when chains and tapes cannot be used to determine vertical and…

Q: Please explain Part B properly. any classification table is there? How is the order and level…

A: Given: Misclosure= 15mm Total length,K= 10 Km Required: Order of levelling

Q: Within the preceding elements,what should be the preference order for the documents?

A: An order of precedence is listed to resolve any disputes that arise from the conflicts between the…

Q: Show complete solution. Draw all necessary diagrams/illustrations. Using elastic method, compute the…

A: The given figure is shown below:

Q: For Problems 9.1 through 9.6, use the virtual work method to determine the deflection of each of the…

A: A truss is supported at A with a pinned support and at D with a roller support.Three-point loads of…

Q: II. If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of 94 kN as…

A:

Q: Q# Analyze the following stress element for principal stresses, maximum in-plane shear stress and…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Describe ASTM and AASHTO Test Procedure Designations.

A: ASTM and AASHTO

Q: SITUATION A Bearings Length Course L (m) АВ N 48°20' E 529.60 ВС 592.00 CD S 7°59' E 563.60 DE…

A: We have to asked bearing of line DE & bearing of line BC & find total area.

Q: A cut is to be made in clay for which the cohesion is 40 kN/m² and = 0. The maximum safe depth of…

A:

Q: Determine (a) the shear strains at all corners and (b) average normal strain that occurs along…

A:

Q: Provide an example of a product or system that uses international standard (such as bank card size ,…

A: There are several aspects where the standards are followed internationally. In case of traffic…

Q: 2. The magnitude of the three forces acting on the plate are F₁ = 100KN, F₂=80kN and F3= 50kN. Solve…

A:

Q: "repository, modeling tool, documentation instrument, engineering instrument, and construction…

A: Repository- A repository is a location, space, or object where something is placed or kept.…

Q: The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20…

A: Given, Thickness of the vessel, t= 26mm Number of bolts= 20 Diameter of the bolts= 20mm Outer…

Q: Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have,…

A: Consider the given data The coordinate of the point A 60,0,0 The coordinate of the point B 0,120,20…

Q: Describe government standards?

A: Government is defined as the group of people or a system in operation which has the right of…

Q: Write the definition of standard specification?

A:

Q: 50 units 50 units A B C Which rivet is least likely to fracture first? a O A b O B C Ос d The rivets…

A:

Q: The construction document set consists of which of the following documents?

A: To find :- The construction document set consists of which of the following documents?

Q: A surveyor forgot to note the distance and bearing of a line while performing a close traverse.…

A:

Q: -Determine the hourly cost of owning and operating of an equipment and as follows: Engine 160 hp,…

A: To determine the hourly cost of owning and operating the equipment, we need to consider various…

Q: What sections of the specifications are applicable?

A: Concept: Specification describes the nature of the work, class of the work, materials utilized in…

Q: Situation E An engineer's notebook gives the observed magnetic bearings of the following traverse:…

A: Locat attraction:  It is the deviation of true bearings because of presence of magnetic objects . It…

Engineering Standards and Codes

Standards are technical publications designed to ensure the reliability of goods, products, methods, or services. They establish technical requirements, specifications, guidelines, features, or design procedures. Standards recommend a set of tolerance for design, processes, operations, production methods, or equipments used in a particular area. Standards are not legally binding unless they are accepted as code or regulation.