please could you do the shear force diagram for question 2 UFMFH3-30-1Problem Sheet 2Calculate the reactions at the supports of the simply supported beams with UDLS shownbelowQuestion 120 kNUDL = 5 kN/m%3DAВCDlm1m2mRARDQuestion 24.5 kNUDL = 2 kN/mAВCD1.25 m1.5 m2.5 mQuestion 3|20 kN15 kNUDL = 5 kN/m%3DA BV1m2m3m1m3mQuestion 410 kN20 kNAВUDL = 20 kN/mE2.5m2m2m3mRBYREY16

Answered: Image /qna-images/answer/21c16a3e-6ec7-4197-bf7a-c352e398a125.jpg

Answered: UFMFH3-30-1 Problem Sheet 2 Calculate…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

- Please Provide Free Body Diagrams and Kinetic Diagrams.- Please state all equations in variable form first before substituting values for the variables.- Please show EVERY step of the solution, including all steps necessary to solve systems of equations.- once answered Correctly will UPVOTE!!
HANDWRITTEN solutions only please! Thanks
2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, = 500 mm, an outside diameter of D, = 30 mm, and a wall thickness of t, = 3 mm and segment (2) is a solid shaft with a length of L2 = 800 mm and a diameter of d2 = 20 mm. For the material properties of each segment please follow the table 2 Table 2 Shear Modulus Surname starting (A-M) G, = 26 GPa G2 = 45 GPa Surname starting (N-Z) G = 45 GPa G2 = 26 GPa If an external torque of Tâ = 300 N. m acts at pulley B in the direction shown, (i) calculate the torque Tc required at pulley C so that the rotation angle of pulley C relative to A is zero. (ii) Discuss what would happen if you replace the tube with a solid shaft of the same material and the diameter equal to the outer diameter of tube. Tc. (2) L2 (1)
I'm not sure how to get the final result in mm. Nm = Newton meters MPa = MegaPascals
You are designing a 1/4 inch diameter pin with a yield strength of 50,000 psi to hold 1000 Ibf. You are trying to decide between using the bolt in tension, bending, or double shear. Which setup is more likely to cause the pin to fail (by fail I mean yield or break)? Do not do any calculations for this problem, use your general understanding of the three different load cases. Double Shear Pin 券 Tension TT Pin Bending Pin O Tension O Bending O Double shear O All are the same
How can I find the reactions, shear force and bending moment in this problem?
Draw the shear diagram for the beam. Follow the sign convention. (Figure 1) Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note - The curve you choose from the drop-down is only a pictorial representation of a real quadratic/cubic curve. The equation of this curve is not mathematically equivalent to the correct answer. Consequently, slopes at discontinuities and intercepts with the x-axis (if any) are not accurate. ? 4 kip/ft A 12 ft 12 ft No elements selected V (kip) 50 T 40 30 20 10 I (ft) 12 18 24 -10 -20 -30 -40 -50 Add discontinuity lines and select segments to add to the canvas.
For the figure shown below (not to scale)... (a) Write equations for the internal forces at J (axial (F), shear (V), and bending (M)) in terms of only P and a. (b) Graph your equations as functions of P, using a =45°, from 0
Help!!! Please answer Correctly !! Clearly solved Please !!!!!!!!
FIGURE PS-66 500 N/m 0.60 m 1 Compute tbe reactions at the supports using the toch niques shown in Section 5-2, 2 Draw the complete shearing force and bending noment dagrams using the techniques shown in Sections 5-3 through 5-8, 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment
Perform double integration of the bending moment equations. You will obtain deflections in this form (can be found in the image attached) Calculate: the value of the constant integration C2. Enter your answer in kNm2 to three decimal places. b) the value of the integration constant C4. Enter your answer in kNm2 to three decimal places. c) the value of the deflection at point C. Enter your answer in mm to three decimal places.
The state of stress at a point in an engine piston is given in the x-y-z coordinates by: 90 180 [0]=0, MPa = 180 240 yx yy 120 zy Using the matrix transformation law, determine the state of stress at the same point for an element rotated about the x-axis (in the y-z plane) 60° clockwise from its original position. Calculate the stress invariants and write the characteristic equation for the original state of stress, Calculate the deviatoric invariants for the original state of stress, Calculate the principal stresses and the absolute maximum shear stress at the point. What are the stress invariants and the characteristic equation for the transformed state of stress, а. b. С. d. e

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS