uestion 2 A rotational mechanical system is described by the 2nd order differential equation, d²e(t) dt2 d0(t) + KO(t) = T,(t) dt +B where T:(t) is the input torque, 0(t) is the output angular displacement and J, B and K are the system inertia, damping constant and spring constant respectively. The system is initially at rest, i.e. 0(t) = de(t) O and = 0. At time t = 0, the input torque to the system undergoes a step change from 0 to dt 12 Nm. The resultant angular displacement of the system due to the applied torque is shown on Figure Q2. () Find the spring constant 'K', the damping ratio 'c', system Inertia 'J' and damping constant 'B'. (ii) Write the system transfer function. (ii) What is the system undamped natural frequency? 0.12 0.1 0.06 0.02 2.5 3.5 4.5 Figure 02 Displacement (rad)

uestion 2 A rotational mechanical system is described by the 2nd order differential equation, d²e(t) dt2 d0(t) + KO(t) = T,(t) dt +B where T:(t) is the input torque, 0(t) is the output angular displacement and J, B and K are the system inertia, damping constant and spring constant respectively. The system is initially at rest, i.e. 0(t) = de(t) O and = 0. At time t = 0, the input torque to the system undergoes a step change from 0 to dt 12 Nm. The resultant angular displacement of the system due to the applied torque is shown on Figure Q2. () Find the spring constant 'K', the damping ratio 'c', system Inertia 'J' and damping constant 'B'. (ii) Write the system transfer function. (ii) What is the system undamped natural frequency? 0.12 0.1 0.06 0.02 2.5 3.5 4.5 Figure 02 Displacement (rad)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When an electric machine works, due to the intenal losses, it starts to heat. Which is the duration of the heating transient? O (a) Can be determined only graphically 21 jmo O (b) It depends on the ambient temperature O, amb O (C) It depends on the rated power of the machine P O (d) It depends omn the thermal time constant of the machine T, rated th p1070
Electrical Engineering _ control system, Notes : pls try to solve in less than 30 min.
(i) (ii) X X X Im Im Ot ► Re ► Re y(t) y(t) For each pole-zero plot, sketch the expected step response based on the dominant dynamic behaviour of the system. The answer for (i) is provided as an example. m
In the circuit shown, the coil has inductance and resistance. When X is joined to Y, the time constant is I during growth of current. When the steady state is reached, rate of production of heat in the coil is "P" joule/sec. X is now joined to Z, and after long time of joining X to Z- (A) the total heat produced in the coil is Pt (B) the total heat produced in the coil is Pt (C) the total heat produced in the coil is 2Pt (D) the data given is not sufficient to reach a conclusion
answer this question woth a free body diagram and explain each part of the question to the final answer
Please Solve it ASAP ELECTRICAL MACHINES tq
PIease answer correctly
QUESTION 1 A motor is an electromechanical component that yields an angular displacement output for a voltage input, that is, a mechanical output generated by an electrical input. Figure (a), (b) and (c) below shows the motor's schematic, the block diagram and a typical equivalent mechanical loading on a motor, (0) R₂ 0000 Armature (1) circuit (a) Tm(1) (1) fro Fixed field elle Rotor Tm(1) ein E (s) Dm G(s) (b) 0,(x) (C) where Ra and La are the resistance and inductance of the armature circuit, vo(t) is the voltage generated in the armature circuit. Tm(t) is the torque developed by the motor, Jm the equivalent inertia, Dm the equivalent viscous damping, ea(t) the input voltage, and Om(t) the angular displacement output. Part 1. If given the torque T (t) = Ke (t)-K₂ differential equations to describe the relationship between input ea(t) and output Om(t) in time domain. Then derive a transfer function Om(s)/Ea(s) in the s-domain which models the motor. Part 2.. For the transfer function…
Kindly answer these questions
A coil with 200 turns is linked with the flux given by o(t)=2tcos(6t + 34° )Wb. Determine the magnitude of the voltage induced in the coil at 3.5sec. Show your complete work.