Two wires AC and BC are tied at C to a sphere that revolves at a constant speed v=14 ft/s along the horizontal circle as shown. (Figure 1) Figure A B 30⁰ 45° < 1 of 1 > 6 lb Part A Determine the tension on wire BC (TBC). Express your answer to three significant figures and include the appropriate units. TBC = 251.30 μA Submit Previous Answers Request Answer X Incorrect; Try Again Part B Submit lb Determine the tension on wire AC (TAC). Express your answer to three significant figures and include the appropriate units. μA TAC = 251.30 lb ? Previous Answers Request Answer P Pearson ?

Q: The bar is supported by the thrust bearing A and the cable BC as shown in (Figure 1). Suppose that F…

A: We need to findReaction at point A

Q: y M 0.4 m/ 45 0.6 m 0.4 m For the above diagram, there are smooth journal bearings at supports A, B…

A: The value of force is The moment applied is The distance y is

Q: The frame in the figure is a counter-balance scale used for decades to offer products. Calculate the…

A: Given data, The distance of EFG is 350 mm. Value of b= 200 mm x varies from 10 mm to 400 mm. Mass of…

Q: A beam is held by 3 bars of the same material/Elastic Modulus, length and same cross-sectional area…

A:

Q: Suppose that F1 = 19 kN. a) Determine the x and y components of reaction at pin A using scalar…

A:

Q: the magnitude of component parallel to the hinge axis of the door, (include units with answer) A:…

A:

Q: Q2. As shown on the right in image below, the force Facting on the box varies with displacement s,…

A: Given data  Coefficient C = 18  Find the work done by the force to the box when the has displaced s…

Q: 1. A 100lb weight is suspended by three cables as shown in the figure. The ratios of the stiffness…

A: The mass of the block is m=100 lb. The ratio of stiffness of cables are in ratio AP:BP:CP=2k:k:3k

Q: #2 A 100 kg plate is supported by cables CD and CE and can rotate about hinges A and B. Write an…

A:

Q: Use the following information for the system shown below: 1. The object (T-beam) is shown in black.…

A:

Q: A force of 10 lb is applied to the cord. Block A weighs 27 lb. Neglect the mass of the pulleys and…

A:

Q: Two wires AC and BC are tied at C to a sphere that revolves at a constant speed v=14 ft/s along the…

A: Introduction We will compute the tension in the cable AC and BC in this case by first considering…

Q: I have attached an image. In this image, there are value of spring constant (k) for hookes law…

A: When two springs are in series, the resultant spring constant is given by 1keq = 1k1+1k2Where k1 and…

Q: Equilibrium of a particle: ΣF = 0 .. ΣF = 0 and Fy Find the tensions in the two cables which are…

A: Given data  Mass = 10 kg h= 2.5 m d1= 3.75m and d2=3.75m Find the tension in cable AC and BC

Q: Q1 The frame structure shown below is in static equilibrium. Find the forces acting at pins C and D.…

A:

Q: A force F, F above Figure with respect to point C, using CA and TCB. Given conditions di 18N, acts…

A: Force F = 18 N d1 = 5m d2 = 8m d3 = 5m

Q: Each block in (Figure 1) has a weight of 430 lb. Figure k = 800 lb/ft μ = 0.5 A Mg = 0.2 B P 30°…

A:

Q: The bar of negligible weight is supported by two springs each having a stiffness 180 N/m The springs…

A: Given data  Stiffness = 180N/m Find the angle with the horizontal

Q: Two wires AC and BC are tied at C'to a sphere that revolves at a constant speed v=20 ft/s along the…

A: The weight of the sphere is .The radius of curvature is .The gravitational acceleration is .The…

Q: If F = 810 N , determine the tension developed in cables AB, AC, and AD

A: Given that: F = 810 N In the given configuration, it is required to determine the forces developed…

Q: 7. The system shown below includes a block and spring on an inclined plane. Answer the following…

A: The system energy remains constant when net work done by the conservative forces are zero in a…

Q: In (Figure 1), the tension developed in cables AB and AC cannot exceed 450 lb. Part A Determine the…

A:

Q: Use the method of SECTIONS to find the true magnitude a direction in bar HG of the truss shown below…

A: Give. Data is

Q: An ideal spring, with a pointer attached to its end, hangs next to a scale. With a 100N weight…

A:

Q: 2.18 A 200# stone is being lifted off the ground by a lev- ering bar. Determine the push P required…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.