Two vertical conical tanks are joined at the vertices by a pipe. Initially the bigger tank is full of water. The pipe valve is open to allow the water to flow to the smaller tank until it is full. At this moment, how deep is the water in the bigger tank? The bigger tank has a diameter of 6 ft and a height of 10 ft, the smaller tank has a diameter of 6 ft and a height of 8 feet. Neglect the volume of water in the pipeline.

Q: Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute…

A: Given data, Q = 400 gallons/min = 4007.48×60ft3/s density of soil (γoil) = 55 lb/ft3pressure at A…

Q: Two tanks A and B have 80 m difference in water levels, and are connected by a pipe 0.3 m diameter…

A: Friction factor f = 4F = 4×.002 = .008 Total inflow = Total net flow at junction CQ1 = Q2 + Q3Q1 =…

Q: A water tank is 30 ft in diameter and the normal depth is 25 t. The outlet is a 3-in horizontal pipe…

A: Given: The diameter of the tank is 30 ft. The normal depth is 25 ft. The diameter of the outlet pipe…

Q: Methanol (SG = 0.8335, viscosity is equal to that of water) is being transported from a very large…

A: In this question we use formula: 1. Reynold's Number formula = (Density × u ×D)/viscocity 2.…

Q: A pump is used to draw water from an open reservoir to an open tank on the top of a building. The…

A: Given,  Flow rate (Q) = 50 L/s or 0.05 m3/s Static head (Hs) = 6 m  Static discharge head (Hsd) = 20…

Q: The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B C The end Cis an…

A: Option(2) is the correct answer

Q: A 300 mm x 75 mm horizontal Venturi meter is inserted in a 300 mm diameter main pipeline where water…

A: Compute the difference in pressure head from the inlet to the throat?

Q: A pump feeds 100,000 lbs/hr of mirbane oil @ a temp. of 68OF (sp.gr. = 1.21, µ=2.15 x 10-3 Pa-s)…

A: O.D = 89mm t(thickness) = 4mm I.D. = O.D - 2t = 89-8 = 81mm = 0.081m l (length of pipe) = 45m kgate…

Q: Water flows downward through a vertical 10-mm- diameter galvanized iron pipe with an m average…

A:

Q: ISTINYE ISU UNIVERSITY Question 2: A steel pipe is used to drain water from a reservoir that is 50 m…

A:

Q: 2. From the figure shown, pipe AB is 400m long, 200 mm in diameter and f= 0.003, pipe U is 300 m…

A: PipeLength (L)  mDiameter (d)   mFriction factor…

Q: Consider a constricting portion of a pipeline carrying water vertically downward as pictured. At the…

A: Given:-  Diameter at point 1 (d1) = 7 inches  Velocity at point 1 (V1) = 10 ft/s  Height of point 2…

Q: A short horizontal pipe connects the bottom of two tanks with axes vertical. One, a cylinder 8 ft.…

A:

Q: Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33…

A: Given data: Pipe 1: Diameter of pipe A D1 =30 in  Length of pipe A L1 =5000 ft Pipe 2: Diameter of…

Q: problem 4 A vessel has two identical orifices A and B with identical values of C, provided on one of…

A:

Q: Which of the following statements about Energy Grade Line (EGL) and Hydraulic Grade Line (HGL) is…

A: different statements about energy grade line (EGL) and hydraulic grade line (HGL)need to find the…

Q: Tow oil tanks are connected with a pip that has a constant radius, the readings of the two gauges…

A: Given data in question  Pressure at point 1 and 2 Elevation head at point 1 and 2 Specific gravity…

Q: Problem 5 Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5…

A: Given that,Area at section 1 = 0.8 ft^2Area at section 2 = 0.2 ft^2Flow rate Q = 5 ft^3/sHead loss =…

Q: A circular pipeline stretches 202 miles from an initial elevation of 510 ft to a final elevation of…

A:

Q: Determine the weight of the block

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: At two points '1' and '2' in a pipeline, the velocities of fluid are v and 3v respectively. Both…

A: Bernoulli's theorem : According to Bernoulli's theorem, if the fluid flows horizontally with no…

Q: Water at 10°C flows through a branched pipe system as shown. Branch 1 is 400 m. long and branch 2 is…

A: Given Data: The data is given as: Diameter of pipe1(d1)=0.075mDiameter of pipe2(d2)=0.1mLength of…

Q: Flow over lengthy pipelines is seen in oil processing. A pipeline with a 4-inch schedule 40 steel…

A:

Q: This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The…

A:

Q: pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in…

A:

Q: The 6 inch pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzle having a…

A: The given figure is shown below:

Q: In a horizontal 5-inch pipe (ID = 5 in.), water is being delivered at a stable discharge of 25…

A:

Q: Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 cfs. What is…

A:

Q: 2. A nozzle 3 m long has a diameter of 1.3 m at the upstream end and reduces linearly to 0.45 m…

A: Figure is as shown

Q: A pipe system is comprised of a flush entrance, one gate valve, one 90° elbow, one 45° bend, and a…

A:

Q: A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the…

A:

Q: 2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges…

A: We have to find the pressure at A in the mid point of the pipeline according to the given data like…

Q: The tank shown in the following figure is being filled by Pipes 1 and 2. The water level is to…

A:

Q: The graphic below shows a reducing section that is part of a vertical pipeline. The pipeline…

A: Given, S = 0.8 Q = 0.6 m3/s P1 = 200 kPa L = 450 mm or 0.45 m

Q: Calculate the static pressure (in psig) at a location in the line 200 feet further along flow…

A:

Q: With the given pipe lengths, sizes and connections and if all pipes have an f=0.020, determine the…

A:

Q: A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of…

A: what is the static pressure of the water at the outlet,P2=?

Q: 0 ft (assume this is 1000.00 ft). The flowrate in the system from ervoir is 5 cfs. Assume the water…

A: Solution-   (a)  Hazen williams equation:        hf =4.73lQC1.852-1d4.87    here , For first 1000 ft…

Q: 2. A nozzle 3 m long has a diameter of 1.3 m at the upstream end and reduces linearly to 0.45 m…

A: As per Bartleby policy i can answer  only one question at a time. Please upload other questions…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?