Two tugboats are towing a Cargo ship as shown in Fig.1. Tugboat A exerts a force of 15OON at 30° while tugboat B exerts a force of 20,000N at 50°. Determine the magnitude and direction of resultant force acting on the cargo ship. Show it in a sketch. 10N A 30 Cargo ship 50° Fig. 1

Q: The rectangular gate shown in Fig. Q.B1 is 2 m wide (perpendicular to the paper and is hinged about…

A: Given : This is a fluid mechanics problem where we are asked to determine the torque M on the shaft…

Q: For the beam loaded as shown, determine the maximum shearing force and bending moment developed.…

A:

Q: From the continuous beam show, determine the reaction at B in kN El is constant. 250 kN 20 kN/m B E…

A: For given beam,find reaction at B Here for continuos beam,we will use slope and deflection method to…

Q: PROBLEM 2: Find the resultant of the applied forces on the beam that is loaded as shown.

A: The given beam has point load , moment , uniformmly distributed load. Rectangular load on beam…

Q: 1) A truck and trailer combination having the axle loads as shown in the figure rolls across the…

A: Given- A simply supported beam of span 10 m  carrying a truck and trailer combination of load.…

Q: For the beam shown in Figure (2), if the resultant force is 30 kN directed vertically downward.…

A:

Q: Draw shear force and bending moment diagram by using graphical method. 80 kN/m 6 kN/m 4 m 1.5 m RA…

A: Draw SFD and BMD

Q: The overhanging beam shown has various forces and a 2.5 N m moment applied to it. The 2.5 N m moment…

A: As the distance between the forces will be: d=0.4+0.2+0.5+0.1=1.2 m

Q: compute the support reaction, for the beam ABCDE shown in following figure

A: Given that,

Q: Consider the loaded beam in the figure below: the closest number to vertical reaction force at A…

A: Let reaction at A is RA Moment at C is zero, thereforeRA×9-24×6-24×3×1.5 = 0RA×9 =252RA = 28 kN

Q: 10 KN 20 KN 30 KN 3m 5m A steel beam 12 m long is simply supported and carries the moving wheel load…

A: Given  Length of beam = 12 m

Q: Force A has a magnitude of 200lb, and points 35° N of W. Force B points 40° E of N. Force C points…

A: For solving these type of question we have to find x and y components of forces and then use the…

Q: PROBLEM 1. Given are the loadings of the beam in the figure. Assuming all bearings are frictionless.…

A: Introduction- The girder is a structural element which predominantly resists load delivered…

Q: 23 kN 7 kN/m 5.1 kN/m A 2 m 3.6 m 2.6 m

A:

Q: An beam 8m in length, with a hinge support at x=0, and a roller support at x=6 is subjected to a…

A: The FBD of the beam is shown below:

Q: A 6-m simply supported beam AB supports a trapezoidally distributed load . The intensity of the load…

A: Divide the load into two typesudl=25 knmTraingular load=0 to 25knm  at B

Q: Q.12 An aluminium bar (E = 70 GPa, µμ = 0.33) of diameter 20 mm is stretched by an axial force P…

A: Given - An aluminium bar, E = 70 GPa,  μ = 0.33  Diameter = 20 mm Due to an axial force diameter…

Q: Compute the reaction forces in B and D. After solving the problem, answer the following question:…

A: Given: Loads acting in the negative x direction is 5.4kN and 5.4kN on joint A and C respectively.…

Q: Refer to the figure, what is the horizontal reaction at support A in kN? 12 kN 3 m 3 m C D 4 m 8 m…

A:

Q: The figure shown is a beam subjected to varying loadings and a point load. a) Determine the…

A:

Q: Problem 2 6200 lb Determine the magnitude and direction of the resultant of the three forces acting…

A: Open the force compoment along the x direction and y direction.

Q: 100 kN www 64 kN www 82 kN www 82 kN ww 55 kN www 2m A В 3 m 3 m 3 m 3 m 3 m 3 m 91 kN 73 kN 46 kN…

A:

Q: An overhanging beam AB is loaded as shown in the figure and is resting on roller support at A and…

A: Given data:

Q: Where must the 2.2 kN force be applied so that the bar A whose mass is negligible will be in…

A: The equilibrium in the body provides stability to it, the conditions are as follows : The body is…

Q: Determine the resultant of the force system shown & y intercepts. Y 300)

A:

Q: 2 kN/m 6 m 1 m B. 理 出版。

A: By Internal Force diagrams here, means the Shear Force Diagram, Bending Moment Diagram, and Axial…

Q: A concurrent force system has six forces as shown in Figure Determine the following: A. Magnitude of…

A:

Q: QUESTION 1 A continuous beam ABCD is shown in Figure Q1. 1.1 Calculate the magnitude of the…

A: A continous beam ABCD is given asTo find:-Reactions and bending momentsShear force and bending…

Q: w(x) = [2.5x – 0.1x²] kN/m A B 20 m

A: The distributed loading is defined as, wx=2.5x-0.1x2 Consider a strip of thickness dx. The area of…

Q: The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth of a…

A:

Q: Q1: For the beam Shown in Figure 1. Use the data from Table 1. Find the following: The reaction at…

A: Given data  Point load  UVL Distance  Overhang.

Q: Problem 03: Compute the determinacy and support reactions for the beam shown below. 10 kN 40 kN A В…

A:

Q: Engineering Mechanics Draw the figure. Put the directions if clockwise or counterclockwise and if…

A:

Q: Problem 1.9 - Determine the magnitude and direction of the resultant force acting on the…

A:

Q: 4 kN 1.2 m 1.2 m 1.2 m 2.8 m 6 kN 45° 5 kN

A: Resultant Force: A single force that represents one or more forces acting on a structure is known as…

Q: A box of weight 100 kN shown in the figure to be lifted without swinging. If all the forces are…

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.